+ c% Q+ r, y1 S% J5 BSorry, You've got a bad luck ) w. v7 k: w8 I0 {" }% N2 R Win XPSP3 has a bag with reading intermediate toolpath results file in HSM 2.3.3.6892 .. So it can not build a toolpaths...- T* m: p# k' ~8 ?2 K
4 L$ [% l7 I! c1 r
[ 本帖最后由 solid_user 于 2008-9-16 05:28 编辑 ]
! x# l- L" D% C8 s1 S% EI don't know.. If you have got a newer than HSM 2.3.3.6892 Installation for Mc9.1 I can try to make a crack. Maybe it will be work under Windows XP XP30 a4 _3 F. r' I% j; F* O
0 j$ p6 l' M; S) lBTW HSM 3.0.31 for MC X-X3 is already released om cimco-hsm.com , V9 `1 q7 D) N" o% V( [2 O% h: @
error: failed to read from kernel stream (please try to repair the installation) 0 m4 ?' G( T" g/ q6 j2 z, Aerror: toolpath generation failed / D- K3 K5 E3 C( o
8 K2 x) y' i" ?
I think I have to change the system
原帖由 joks 于 2008-9-16 06:11 发表 http://www.3dportal.cn/discuz/images/common/back.gif 6 s; o" E& S0 V- K* Herror: failed to read from kernel stream (please try to repair the installation) ( }4 F( X5 k1 t5 d+ }) l; g; cerror: toolpath generation failed 3 |8 e: J' M0 }: ]+ _) ^% `
- R; v( C. i+ e3 P" t
I think I have to change the system
& z w0 r$ }! n* s* X
That's bug of Win XP SP3 I said... . P8 J3 X: Y$ x8 D" `) LIn Win XP SP2 all works and you will not get that message & {/ Q1 |( M/ N \' ?2 @ . }) [: N. i7 C. |+ A/ z3 T[ 本帖最后由 solid_user 于 2008-9-16 06:37 编辑 ]
2 e. g6 z2 m! Z( n$ ?$ mI use different OS's on different computers.. 7 f2 ^* W; ]/ z1 jAs for HSM 3.x.x it's good but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it?/ _% G K3 y5 z2 G
; b& h V$ u2 l% s+ v% L& x5 T
BTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi ; C6 X4 a3 t4 U6 h0 q# o; S& E5 ?2 \" a Z: s. V
[ 本帖最后由 solid_user 于 2008-9-16 06:45 编辑 ]
I use different OS's on different computers.. = Oh!$ [% ^' R$ R" @ y. c1 X
: p# R' \" r. B% [3 v& T; O* ~As for HSM 3.x.x it's but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it? = Yes! I started learning is the most Mastercam, I like mastercam! + l9 [7 B. T9 f" O2 P# z ( w" c$ Y4 g8 r2 y6 h$ tBTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi = Moldplus_10_SP0_for_X3 can use it without Crack ?
error: failed to read from kernel stream (please try to repair the installation) R# ]6 _2 W7 {: E; R! T) Merror: toolpath generation failed 3 s/ ]! T) P) M, E, \* G- h% {
WORK IN SP2
error: failed to read from kernel stream (please try to repair the installation)% S2 z# z9 a) F
error: toolpath generation failed 2 K/ ~0 Y4 G& U! aWORK IN SP2
原帖由 ryanhe2008 于 2008-9-17 10:56 发表 http://www.3dportal.cn/discuz/images/common/back.gif! A( i6 G. E& a
error: failed to read from kernel stream (please try to repair the installation) 2 z6 g4 Z* h" Z' |1 Oerror: toolpath generation failed & f" z7 v& G5 R, C, ]8 I$ T; e
WORK IN SP2
* _+ }' G- G: B6 c2 iI suppose that you have install some of Windows XP2 Update wich couse this bug..$ }' V. S4 S" h3 Q# n9 m! p
In any case it's bug of Windows..
发表于 2008-9-16 03:48:05
Sofa! Thank you very much
" u% J5 U- v! Q$ b0 y6 K7 r
楼主
) w. v7 k: w8 I0 {" }% N2 R
. I' s& W) {9 E# U. k
Oh!$ [% ^' R$ R" @ y. c1 X
Yes! I started learning is the most Mastercam, I like mastercam!
Moldplus_10_SP0_for_X3 can use it without Crack ?