|
|
楼主 |
发表于 2012-4-10 20:20:54
|
显示全部楼层
来自： 中国天津
本帖最后由 86843173 于 2012-4-10 20:24 编辑
x- h5 ?$ b- ?- s( W j) y e- r
9 R6 m( E9 @/ g3 y我说的是车床0 S: x( V4 m( \2 ?: Y
# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
0 Z6 x' T% m3 b- b7 k# --------------------------------------------------------------------------
2 j4 u. B) f" r#Default english/metric position format statements
# u% r& T5 a0 V4 _" \6 Kfs2 1 0.7 0.6 #Decimal, absolute, 7 place, default for initialize (
; i( A8 c) f- y' p' c. M6 {fs2 2 0.4 1.3l #Decimal, absolute, 4/3 place S$ V; J( B6 e3 n" J. q I
fs2 3 0.4 1.3ld #Decimal, delta, 4/3 place- j1 c& k" n$ u- W8 p- N7 f
#Common format statements# s+ E; R, y) P# z5 ^
fs2 4 1 0 1 0 #Integer, not leading, [7 {2 H, K) z$ v
fs2 5 2 0 2 0l #Integer, force two leading
; Y! r/ ^( e6 P" ]fs2 6 3 0 3 0l #Integer, force three leading* J1 Q6 p# x) h- f7 c0 U
fs2 7 4 0 4 0l #Integer, force four leading. e" F1 i& B. N4 Q5 }9 A
fs2 9 0.1 0.1 #Decimal, absolute, 1 place. a3 I' L2 n( l5 S+ a( E" ~
fs2 10 0.2 0.2 #Decimal, absolute, 2 place
3 p) b8 w8 k: r1 qfs2 11 0.3 0.3 #Decimal, absolute, 3 place
0 C4 x; c8 P' x; X% ^* B' k9 tfs2 12 0.4 0.4 #Decimal, absolute, 4 place/ U8 J8 Z4 P8 t5 U0 m
fs2 13 0.5 0.5 #Decimal, absolute, 5 place) R3 L; G3 _. b1 S& L
fs2 14 0.3 0.3d #Decimal, delta, 3 place* U3 q) X9 r" R3 u7 [
fs2 15 0.2 1.1l #Decimal, absolute, 2/1 place (feedrate) 就是这里4 w+ t0 r9 A, r9 X
fs2 16 0 4 0 4t #No decimal, absolute, 4 trailing1 ]. {$ @, H) p6 z0 }) ]1 k) P/ I
#Default english/metric feed format statements! ?$ c* ~8 J- r) x R
fs2 17 0.2 0.1 #Decimal, absolute, 2/1 place+ e; w' \9 W- q- H) j# a$ J( ^
fs2 18 0.4 0.3 #Decimal, absolute, 4/3 place
7 X* F3 ?9 |2 a' M+ W6 l4 E- |& Efs2 19 0.5 0.4 #Decimal, absolute, 5/4 place `: T) K: ^8 z f# F
fs2 20 1 0 1 0n #Integer, forced output8 w( c( z) i. c! h7 j, D) p/ j1 d6 V" X
# These formats used for 'Date' & 'Time'
+ S) t) p, o; v1 P: U; pfs2 21 2.2 2.2lt #Decimal, force two leading & two trailing (time2)/ s- \+ Y! _: d0 ]3 r! Q7 z
fs2 22 2 0 2 0t #Integer, force trailing (hour)1 l! d* D S4 m* P
fs2 23 0 2 0 2lt #Integer, force leading & trailing (min)7 c, R) r8 Y- o2 D9 L9 d0 }/ N
# This format statement is used for sequence number output- v0 O2 Q7 u( G- T$ @$ K
# Number of places output is determined by value for "Increment Sequence Number" in CD
1 [4 z) |. j5 a/ E G# Max depth to the right of the decimal point is set in the fs statement below
p5 S. ^" H0 P( afs2 24 0^7 0^7 #Decimal, 7 place, omit decimal if integer value |
|
发表于 2012-4-9 21:38:45
发表于 2012-4-9 21:51:34
发表于 2012-4-9 23:07:40