[分享] Siemes Solid Edge ST3 32bit / 64bit Full English (by SSQ)

为什么没有standard parts Administration???
; \( H7 n$ `. C. |; Vkwaikeong1402 发表于 2010-11-8 09:42 http://www.3dportal.cn/discuz/images/common/back.gif

第二张光盘里面吧( @/ |: ]+ O. l8 X0 R" U
三十二位和六十四位全部一共有五张光盘，第三张标准件共用。
0 m, P& b  E6 x$ |" \6 u5 U" ~) L关西无极刀 发表于 2010-11-8 10:16 http://www.3dportal.cn/discuz/images/common/back.gif

请问在以下的那一个？？( n* ]7 f5 `) T5 ^

1 K( D9 n# p9 s! \1)Solid Edge ST3 32bit Accessories Setup/ D. f. |* d9 X+ U1 ]: q
2)Solid Edge ST3 32bit/64bit Standard Parts Setup
) {5 f/ }) ^3 y( c# r" M: }- ?kwaikeong1402 发表于 2010-11-8 13:17 http://www.3dportal.cn/discuz/images/common/back.gif

2all
, E2 v2 t$ t4 t  P  DATTENTION!
# }$ w' B1 s3 ]+ N; PIn SE_ST3_32bit_Eng_SSQ setup instalations for Standard Parts Administration and Structure Editor are missed
7 Q/ [3 a2 Y# q1 Z* t" YHere are links for missed setups
- r# G% ~  g5 S3 t( {* s6 \4 Y5 V* H0 b0 y& Z. ]9 y  e, n* S* q
       Solid Edge ST3 32bit Standard ...' N) U& N% Q  i9 S4 M$ J
solid_user 发表于 2010-11-8 22:07 http://www.3dportal.cn/discuz/images/common/back.gif

2all
2 `/ `0 K& c; F  QATTENTION!: f5 \0 k7 R0 E. M
In SE_ST3_32bit_Eng_SSQ setup instalations for Standard Parts Administration and Structure Editor are missed
$ m4 s, i9 `4 P* Q! [$ _Here are links for missed setups! t$ ]) o7 W# N6 n- ^
9 P' A0 B% D" N2 \9 y
       Solid Edge ST3 32bit Standard ...
0 v, ^8 ~, f- O9 {4 n9 R3 z$ nsolid_user 发表于 2010-11-8 22:07 http://www.3dportal.cn/discuz/images/common/back.gif

为什么没有standard parts Administration???
8 b/ I* N" Y% }8 s( Q) z  c, l$ ^kwaikeong1402 发表于 2010-11-8 09:42 http://www.3dportal.cn/discuz/images/common/back.gif

This is what it represents full installation will proceed ST3 DVD pack photos depict?/ m- r5 q, [. C: P
' N# V9 m4 z2 X$ [! x
3 G! y8 G! ^0 E* _- ~5 z% P
這是你的意思完整安裝包將進行 St3級 DVD的照片描繪?
/ r6 ~" x' o" G4 Edexter1000 发表于 2010-11-9 01:17 http://www.3dportal.cn/discuz/images/common/back.gif

请看看附上的文件..........
5 _6 C9 t: F# M& d. O" p, gkwaikeong1402 发表于 2010-11-9 22:03 http://www.3dportal.cn/discuz/images/common/back.gif

I already install all.....only this 'standard parts Administration' not yet install...7 a5 X, r* \) N" Y+ e+ s
Now I not yet download 'standard parts Administration' , while I download & install it successfully * K- L& S( R8 w, f  k
mean t ...- y3 Y: p) Q4 y( @  `
kwaikeong1402 发表于 2010-11-9 13:02 http://www.3dportal.cn/discuz/images/common/back.gif

Start > All Programs > Solid Edge ST3 > Standard Parts > Configuration Wizard
, }% v1 P3 g- p+ A7 g& dsolid_user 发表于 2010-11-10 05:01 http://www.3dportal.cn/discuz/images/common/back.gif