$ M9 V+ N' I- m, a( q5 C2 R. vSorry, You've got a bad luck ; x5 G o6 D9 a7 L( d0 ? Win XPSP3 has a bag with reading intermediate toolpath results file in HSM 2.3.3.6892 .. So it can not build a toolpaths... % z" i( i% @/ J9 }1 b/ [ 5 J g% p. K! l1 i9 r- r[ 本帖最后由 solid_user 于 2008-9-16 05:28 编辑 ]
+ e6 p/ d6 F5 ^) u/ L8 P! UI don't know.. If you have got a newer than HSM 2.3.3.6892 Installation for Mc9.1 I can try to make a crack. Maybe it will be work under Windows XP XP3- O& v; o# Z7 y9 o' N" x! y/ }
. q/ a$ i6 O5 f" Y0 y" {; eBTW HSM 3.0.31 for MC X-X3 is already released om cimco-hsm.com 9 x) r P2 G3 l) A9 Q$ o# p
1 t4 B+ c4 O% C1 h, C
[ 本帖最后由 solid_user 于 2008-9-16 05:49 编辑 ]
error: failed to read from kernel stream (please try to repair the installation)( c( l7 t" B0 U
error: toolpath generation failed 2 F+ ~) I, O, Z' n' j4 U" d# u9 D( }3 n9 z: F
I think I have to change the system
原帖由 joks 于 2008-9-16 06:11 发表 http://www.3dportal.cn/discuz/images/common/back.gif2 f6 n. S& H0 T7 c
error: failed to read from kernel stream (please try to repair the installation) / i* `# R) b/ M! [error: toolpath generation failed 9 x, f! r0 ^: t) y) x# e' ~ 2 r6 [" ]5 G" i- [I think I have to change the system
7 B/ E/ m" }& WThat's bug of Win XP SP3 I said.... [$ Y8 @5 Z L# \3 l
In Win XP SP2 all works and you will not get that message 5 n- s1 t+ ]6 z# n' d a7 Y8 k
# |6 p, {% N( d( k2 @4 w5 W7 cI use different OS's on different computers.. ; N) `0 x9 y. o! X& j. z% V- i( [7 BAs for HSM 3.x.x it's good but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it?8 {3 |' h/ P8 z# N7 }
6 U) r% k6 p# K2 z. @. @% nBTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi 1 e. e( O, r: E& Y. u
I use different OS's on different computers.. = Oh!- R, ^& _) Q( x8 B' K
! N5 R" Q3 Z" J0 C! q. AAs for HSM 3.x.x it's but it can not be run under MC 9.1... I think you need HSM not only for MC X-X3 but for MC 9.1 too.. Isn't it? = Yes! I started learning is the most Mastercam, I like mastercam!. C% c. D8 J5 Y# D2 \
9 r3 Y/ D) N5 `
BTW MoldPlus v10 SP0 for Mastercam X3 is already released on mastercam.fi = Moldplus_10_SP0_for_X3 can use it without Crack ?
error: failed to read from kernel stream (please try to repair the installation) 9 V, m- H/ D! T, V9 q) ?& [5 A5 Nerror: toolpath generation failed ) U- q. h. A. _3 h& m
WORK IN SP2
原帖由 ryanhe2008 于 2008-9-17 10:56 发表 http://www.3dportal.cn/discuz/images/common/back.gif- a1 q( C. d% h. T
error: failed to read from kernel stream (please try to repair the installation)# [' ?% C) n$ d8 M
error: toolpath generation failed 3 o n! c& f# G% [) |
WORK IN SP2
0 N0 I' e' ` A6 V, O
I suppose that you have install some of Windows XP2 Update wich couse this bug..9 c* o0 o- x# t
In any case it's bug of Windows..
发表于 2008-9-16 03:48:05
Sofa! Thank you very much
楼主
; x5 G o6 D9 a7 L( d0 ?
5 n- s1 t+ ]6 z# n' d a7 Y8 k
1 e. e( O, r: E& Y. u
. K7 G4 d9 k! M1 j& }
Oh!- R, ^& _) Q( x8 B' K
Yes! I started learning is the most Mastercam, I like mastercam!. C% c. D8 J5 Y# D2 \
Moldplus_10_SP0_for_X3 can use it without Crack ?