|
|
马上注册，结识高手，享用更多资源，轻松玩转三维网社区。
您需要 登录 才可以下载或查看，没有帐号？注册
x
本帖最后由 lyd_2005 于 2015-10-23 13:54 编辑
! n" q9 \' w5 x6 E7 ~3 \1 |4 C8 p
" b* d" d4 ?7 B$ s! E
. K/ ^* ~4 X1 z3 [3 A) @+ v% r6 @( q( e3 R7 R8 \: [4 z
1.查找 ptap$ #Canned Tap Cycle* j+ ^/ }$ R8 G* w3 ~9 S7 `) i) E
5 n/ ]# J3 n* W* z' f, Z
& o4 }4 M0 X# S8 p1 W" a
到 pcom_movea 中间部分修改为# p2 Q& e. O/ R. S
ptap$ #Canned Tap Cycle& J; z2 S' { T a+ C! G
pdrlcommonb
& K8 l3 l: Z( i4 E if peck2$ = 0,
- y$ Y: R/ V2 Y8 O) C7 j [
$ W# [9 l2 w3 d' V' n0 P; o #RH/LH based on spindle direction5 x+ ?) b+ n: S$ t
if rigid_tap, pbld, *sm29, *speed, e$ #Rigid Tapping
7 N( d6 j5 z/ f) j* k) z pcan1, pbld, *sgdrlref, *sgdrill, pdrlxy, pfzout, pcout, pindexdrl,
# m+ a3 y- c0 J+ D8 ^' V6 U prdrlout, [if peck1$, *peck1$], *feed, strcantext, e$. t! T+ E$ R, c5 k
]
: V* ~ `/ j$ y8 J3 q$ {. G else,1 `. w/ Q K2 ?! B3 M
[$ w8 N/ X u& p
"M03",*speed, e$2 G# g5 ?- h( O" Z9 F
"G94", e$
" p5 U9 o- Z, _4 a& t+ H: q if metvals, pitch = n_tap_thds$ # Tap pitch (mm per thread)
, O5 C( H. C% B5 n8 o8 W: _ else, pitch = 1/n_tap_thds$ # Tap pitch (inches per thread)& w0 }$ R! \2 M) D( s
pcan1, pbld, *sgdrlref, *sgdrill, pdrlxy, pfzout, pcout, pindexdrl,
; [# I/ `+ [: u7 s7 y: J9 D prdrlout, [if peck1$, *peck1$], *pitch, !feed, strcantext, e$; @4 W8 t8 C7 l
]7 A/ c* r' d0 v' i b
pcom_movea2 h2 E4 I! S5 c3 x- j6 i& h+ R+ j
2. [tap]5 e# P p$ c) `0 E) Y/ A/ m7 b
1. "G84/G74 - Tap"& ]* D5 v) H( a
3. ""+ j u/ E4 ?% ^: F0 N7 s7 {
7. "Peck"# ^2 _7 a0 ^+ u2 g. n
8. 将 "" 修改为 "0为G95方式，1为G94" 要冒号（有两处）
7 o4 s$ G% `& i# |3 P 9. ""
* [' N' g, j- g1 H1 d 10. ""
6 V- {1 i- Z, p$ D- p. J 11. "" ?: U' W! B( ^( @( n/ I
3. pcanceldc$ #Cancel canned drill cycle
- c4 y' s/ k' R) T result = newfs (three, zinc)" G: m! M8 ^6 W) k" r* j
if drillref = 0, zabs = initht_a #Make the initht the modal Z value+ }: i) w' I' A
else, zabs = refht_a
8 S1 D1 u( Y# s4 ^7 t! G" o prv_zia = zabs
- ?7 f3 W1 S' R: j8 g- S# v !zabs' ^0 f: B0 s1 F8 i6 b; Y) e; [
ps_inc_calc5 _& x/ g5 z- [0 `5 _! _- ?
prv_gcode$ = zero1 ^8 u) E: i5 X
if cool_zmove = yes$ & (nextop$=1003 | (nextop$=1011 & t$<>abs(nexttool))), coolant$ = zero" ]+ n* d: `3 M' P, A5 m+ j
pcan. c. t" Q/ k# o; w4 P
if drillcyc$ <> 8, pcan1, pbld, "G80", scoolant, strcantext, e$
; g, f+ c4 C& C# d& e/ }4 t if peck2$ = 1,"G95", e$ 增加此行
, F; k: Y7 S7 L5 t0 I2 G #pbld, sgfeed, e$; ^( ?- {4 X# O+ \! J$ m! A
pcan21 Y5 W9 @$ ~9 F2 D# q6 z; Y
因本人不使用此功能，只是一个思路，以上G94，G95,自行调整。
- M0 ?/ `) h: c- N8 e4 m0 T; p" a/ s. w& a b& w9 \7 Z8 L" ^! h
6 e4 Y% u' j0 ^4 z/ \& D* X
9 o, O0 i: h" S |
|
发表于 2015-10-23 12:14:04
楼主
