|
|
发表于 2014-8-19 14:03:52
|
显示全部楼层
来自： 中国辽宁沈阳
Sub main()
% t9 G/ \. y; @Set swApp = Application.SldWorks
1 i8 u; `* R8 _9 J! W" NSet DrawingDoc = swApp.ActiveDoc
' w3 j' @/ C0 a/ [- s' }If DrawingDoc.GetType <> 3 Then Exit Sub$ U& \) G& r: E& `' _ S
Set SelMgr = DrawingDoc.SelectionManager
8 [3 ?3 C ^. m* d9 ?& IIf SelMgr.GetSelectedObjectType2(1) <> 12 Then Exit Sub
3 W+ ^2 l% B9 _1 }3 lSet swview = SelMgr.GetSelectedObjectsDrawingView(1)
) V) H$ d7 s( ~* WSet swDrawComp = swview.RootDrawingComponen
1 e, W: B4 N5 v _( J1 e8 o, [DrawingDoc.ActivateView swDrawComp.View.GetName2
% G8 ? R( j- S- s( |: J. w8 VSet Part = swview.ReferencedDocument
' m0 N( @' r- v8 c9 s! E/ MSet FeatObj = Part.FirstFeature# |1 c6 Q) o }1 b6 D! N! @2 R
FeatObjname = FeatObj.GetTypeName
3 k% d* B# t ~1 M" y' `7 E% iWhile FeatObjname <> "OriginProfileFeature". k# Q* i- @( {; e# l M
Set FeatObj = FeatObj.GetNextFeature! r/ ?0 j! K: q+ p9 D- @( {
FeatObjname = FeatObj.GetTypeName
$ ]$ B( l/ r! s; h/ w4 _/ ?8 eWend
V' O* v' n9 l- `9 n8 p& X+ VFeatname = FeatObj.Name
8 ]+ z* u q) H$ I6 k% y2 o' }! jViewOutlines = swview.GetOutline
6 P' y: B" @7 WViewCXform = swview.GetXform
) U! p. |- q+ @5 z# U" PViewXform = swview.GetViewXform/ A" b$ h T( J* v' Y
Hp1x = (ViewOutlines(0) - ViewCXform(0)) / ViewXform(12), w$ N7 `% Y- X, k7 h# Y
Hp1y = ((ViewOutlines(1) + ViewOutlines(3)) / 2 - ViewCXform(1)) / ViewXform(12)
2 p3 R) Q( U. D$ K3 V& g+ wHp2x = (ViewOutlines(2) - ViewCXform(0)) / ViewXform(12)
6 a- P! O4 G: u2 G2 dHp2y = Hp1y
& o6 s! {5 o Q6 W) n. FVp1x = ((ViewOutlines(0) + ViewOutlines(2)) / 2 - ViewCXform(0)) / ViewXform(12)2 y7 w6 K% |" V1 H4 k6 x" s' r" a
Vp1y = (ViewOutlines(3) - ViewCXform(1)) / ViewXform(12)/ F; E1 r5 L. \9 K; R- \
Vp2x = Vp1x
: M$ M3 G- H KVp2y = (ViewOutlines(1) - ViewCXform(1)) / ViewXform(12) i( d9 _! a/ D# v2 f
DrawingDoc.SetAddToDB (True)
& K& X- ]' [ C, |) c$ B) p% m. JSet SkLineH = DrawingDoc.SketchManager.CreateCenterLine(Hp1x, Hp1y, 0, Hp2x, Hp2y, 0)
; t5 O5 y& P5 ?! j! P9 h' MDrawingDoc.SketchAddConstraints "sgHORIZONTAL2D"
' O+ ~ T7 t& d; k9 q+ fboolstatus = DrawingDoc.Extension.SelectByID2("Point1@" & Featname & "@" & swDrawComp.Name & "@" & swDrawComp.View.GetName2, "EXTSKETCHPOINT", 0, 0, 0, True, 0, Nothing, 0)0 {" W% E$ M' k/ S, G2 L% S ^
DrawingDoc.SketchAddConstraints "sgCOINCIDENT"6 }, X+ k0 |; ?
Set SkLineV = DrawingDoc.SketchManager.CreateCenterLine(Vp1x, Vp1y, 0, Vp2x, Vp2y, 0)
$ I9 c8 O) Z, f( X2 ]% T: DDrawingDoc.SketchAddConstraints "sgVERTICAL2D"
( F1 p/ O0 ~7 ]. `1 h' v( s8 J+ _boolstatus = DrawingDoc.Extension.SelectByID2("Point1@" & Featname & "@" & swDrawComp.Name & "@" & swDrawComp.View.GetName2, "EXTSKETCHPOINT", 0, 0, 0, True, 0, Nothing, 0)
- S- _) C! o3 f, HDrawingDoc.SketchAddConstraints "sgCOINCIDENT"( x3 \ x* V, \" a6 a
DrawingDoc.ClearSelection2 True/ a: y6 m" }3 F( d( a0 T
End Sub |
|
![002902l7x7ddilsxd8losd[1].gif](data/attachment/forum/201408/19/123120fqaceahtic2oawdc.gif "002902l7x7ddilsxd8losd[1].gif")
楼主
& M0 L+ ~! y) K3 @& R/ q' i