|
|
发表于 2009-11-8 00:22:47
|
显示全部楼层
来自： 中国浙江杭州
很简单的，使用一般的外形加工，参数中选第四轴即可
% M9 D! c* Z: N6 X%
9 R( i# u3 _3 Y/ d* QO0000(1)
; w, W3 Y7 S4 H/ R6 R- D9 eG21
% Y1 ~2 J) ~8 b* eG0 G17 G40 G49 G80 G90
2 M Q( J3 W; g9 F. ^$ v- zT2 M64 w: ^) }9 K" B
G0 G90 G54 X-6.976 Y0. A-106.689 S5000 M3
0 G5 W' C$ B" H+ zG43 H2 Z79.5
Z9 `% O* `7 D7 SZ39.5/ _) H1 Z! K9 b, I: W: W& h" g
G1 Z29.5 F50." L. [4 E! z' a+ i7 a% Z
X-7.772 A-105.513 F1000.
0 x) P" d- s" Q4 y. S' cX-7.929 A-105.278$ N7 p' N" \4 y, w! B
X-8.084 A-105.038
$ o$ B+ v' \. H' H* }- X( `" f9 mX-8.237 A-104.792
" B1 K8 \8 @' t" R! U0 w1 |' j* H5 O0 zX-8.388 A-104.5433 `/ W" L3 o# K/ t* a( r8 o, q {
X-8.537 A-104.288
" k5 m7 K, Z0 ? ^2 W6 r7 fX-8.684 A-104.0295 B! w6 H' ?$ |3 [
X-8.828 A-103.766) B' f( R% M3 K/ t; v0 U
X-8.971 A-103.498
0 X+ W" B3 I% J" @X-9.111 A-103.225
# e0 H- t5 W( n/ YX-9.249 A-102.949; o7 E" o# z+ k( O5 {
X-9.385 A-102.668; Q& N8 t$ J4 A; n/ e2 Q
X-9.934 A-101.513 F1426.4$ v5 d& d/ Y$ Q8 d* A. [
X-10.341 A-100.469 F1548.76 [ `" L: s2 ]/ g3 d- O
X-10.554 A-99.81 F1644.5% x1 Q" W B: |0 ]+ h0 i# q
X-10.748 A-99.105 F1712.1
3 A3 v8 W! W. K8 A* ?, h) W8 \X-10.914 A-98.385 F1772.68 a% t: y6 I/ U; {/ X% f) w' B, ` k
X-11.049 A-97.663 F1825.2
/ ~1 ~% D5 G+ S- `" q% TX-11.172 A-96.808 F1870.1
" \; o" \. Z& U. }. A0 WX-11.26 A-95.935 F1905.8
6 G. ~$ I+ E* V* B4 AX-11.313 A-95.04 F1929.3, c9 ]7 B6 V. d) ]( f7 [! A7 U0 ^& P
X-11.333 A-94.025 F1940.8
* r* a+ i2 g1 d: t C8 C: _A-92.1313 T9 m4 j, G( n9 x
A-90.157& ?; I- ?- @) M! v# v, H
A-89.999. Y% b% z+ b9 p4 _ w
A-88.0250 ^5 ?4 W( ~( b. X
A-86.05! [1 W O+ A& W& `0 s% y
A-86.025 |
-
|
