|
|
楼主 |
发表于 2015-11-7 22:00:18
|
显示全部楼层
来自： 中国广东广州
多谢各位现在不用备刀，西门子的备刀我也不懂，我这个程式钻孔是没有问题的，( R) l" O1 c- r$ j1 F
%_N_ 01 _MPF, K7 }, G8 m* I/ |2 L1 X5 t8 [4 R
;$PATH=/_N_WKS_DIR/_N_WD_WPD
9 N, w3 @7 h/ S) s;(***05-11-15*** ***16:37***)
+ |* p; `" A3 U; o7 N, @;(T1 30 BULL-NOSED ENDMILL )
7 d N% q+ Q9 [8 s8 X6 h) |. `* [;(T2 17 BULL-NOSED ENDMILL )
$ C* Q4 c. d% C' o;(T3 26 BULL-NOSED ENDMILL )
- N1 @# ^5 @2 r1 ^;(T5 10 FLAT ENDMILL )
& m; Z! J9 G1 l4 y+ s/ Z# M5 v6 m;(T6 10 FLAT ENDMILL )
" o( @! s5 g A& D7 w;(T106 CHAMFER MILL )
/ t' ^$ ^* A4 t+ x. k u' \1 U;(T7 STANDARD DRILL - 3 ): I5 x p1 i& d0 u' U1 H3 _
;(T9 STANDARD DRILL - 4.3 )
+ S- [5 _/ _- J! F9 _ M! K- X;(T8 STANDARD DRILL - 3.3 )
. J4 {) c# [. f;(OVERALL MAX - Z20.)
" x$ _. J; P$ Z3 e;(OVERALL MIN - Z-22.); }! C k8 s; G7 R
G64 SOFT
, C3 ]% G, _. \G54
6 C5 M8 T: f% B# G3 E4 {3 g. |9 MT1
3 W8 I$ [* ]2 q5 g: L: u1 @M06! }5 T9 h, Q1 q) q" A- y" N
;( 30 BULL-NOSED ENDMILL )
+ s: G6 X8 Q3 A6 E* o; e" u5 vG00 G90 X68. Y-39.344 S2500 M03
% e% k+ x/ \* s' k6 l: W# l& c7 NG01 Z20. F5000, ?$ v+ g9 o# X4 V" \9 Q5 {
M084 R3 @- i1 \$ |! h: x
;(MAX - Z20.)$ T% r( Q3 N" f! R U
;(MIN - Z-5.1)% q0 Z5 Q2 M# o7 B5 O: \
Z2.
& Y; T- [2 W0 D: E6 Y OG01 Z-.425 F3000.* `5 Y+ @- e$ g+ u
Y-8.656 F4000.2 s9 y5 m' W% g2 M# ]/ B9 Q
X-68.2 w' @2 S4 Z0 m# D5 E& \
Y-39.344
, d5 |8 {+ H- F- E6 uZ-.85 F3000.
7 N- p$ T+ D. f( X) U: s' b! UY-8.656 F4000.
' \: v) [$ k2 VX68.
; K$ F0 ]2 M& o: T4 y6 ^Y-39.344, T% D# k, h7 h5 Y+ f6 V* o9 J( [4 X
Z-1.275 F3000.
- ?/ {8 }3 p3 x xY-8.656 F4000.
$ f5 L2 T3 S) n; }X-68.
}3 J: l$ H- ?6 n: y$ k" WY-39.344
3 @9 W" R; q4 o! q8 f* t/ V6 c8 NZ-1.7 F3000.
7 ]! [) \" s' ?Y-8.656 F4000.
4 C4 J; x) H+ CX68. |
|
发表于 2015-11-7 08:48:09
