proe绘图文件设置问题

boylcx

在dtl文件中设好的缺省值，可为什么打开proe进入绘图面板后，总是不加载缺省值？如图片所示！

wjianman

设置好以后要保存你的dtl文件的 或者你可以在dtl文件里面用文本打开直接修改 然后保存

fengbao_02

也有此问题，哪位高手指点下了

boylcx

试过了，不行，才发贴求助的！

wake27

1.检查config的配制,工程图的路径是否正确.2.检查是否有不同版本的配置文件或是不同版本PEO.3.字符是否正确.

seafree101300

要把config放到PROE安装地址的根目录下的TEXT文件夹下

boylcx

我把我的配置贴出来，帮帮俺看看，多谢！我用的是proe 5.0 F000
. ^2 F8 ~( ~5 L* }" mconfig.pro的配置
allow_anatomic_features yes
( ^1 Y0 b' ?* R" k' \bell no
9 s$ T6 I% I! q& idisplay_axes no
' j9 V: g& z6 U  N# f1 ], Bdisplay_coord_sys no
! p. [: p+ V0 C& U% I+ s& V& fdisplay_points no
file_open_default_folder working_directory
intf_out_layer part_layer
4 n; o6 F# `0 A  U- `. ~. cintf_out_text_length full_size
menu_translation both
pro_unit_length unit_mm
0 _) d6 H# H: l1 J1 e9 opro_unit_mass unit_gram
pro_unit_sys mmns
sketcher_undo_stack_limit 100
5 h) Z9 z0 }; n# m. S. btemplate_designasm mmns_asm_design.asm
template_solidpart mmns_part_solid.prt
text_height_factor 30
& Y- P) K" x) a' h( }+ y( h( Sdefault_draw_scale 1.0
dxf_out_scale_views no
template_mfgmold mmns_mfg_mold.mfg
template_sheetmetalpart mmns_part_sheetmetal.prt
5 X: u7 x& s+ S- f( p" |0 o' C( odrawing_setup_file D:\Program Files\proeWildfire 5.0\text\prodetail.dtl
1 H' D& @( `+ b6 q( Ymapkey d @MAPKEY_LABEL绘图;~ Activate `main_dlg_cur` `ProCmdModelNew.file`;\
mapkey(continued) ~ Select `new` `Type`1  `Drawing`;\
/ S) y6 x) A/ G, T# N1 `mapkey(continued) ~ Activate `new` `chk_use_default_template`0 ;~ Activate `new` `OK`;\
mapkey(continued) ~ FocusIn `dwg_create` `inp_model_name`;~ Activate `dwg_create` `psh_ok`;
7 x9 O5 [& d5 [. W9 b2 ?& G- }, Tmapkey e @MAPKEY_LABEL删除;~ Select `main_dlg_cur` `MenuBar1`1  `File`;\
7 y1 T' p( w' R: Pmapkey(continued) ~ Select `main_dlg_cur` `File.cb_file_erase`;\
$ `- P" |- d+ ^0 j- k$ Amapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\
mapkey(continued) ~ Close `main_dlg_cur` `File.cb_file_erase`;\
. t5 Q0 F$ @3 Z# ?- u) v9 p# Vmapkey(continued) ~ Activate `main_dlg_cur` `psh_erase`;~ Activate `0_std_confirm` `OK`;
mapkey n @MAPKEY_LABEL不显示;~ Select `main_dlg_cur` `MenuBar1`1  `File`;\
mapkey(continued) ~ Select `main_dlg_cur` `File.cb_file_erase`;\
3 D$ t( ^1 ^1 W" l& g3 e* o" omapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\
mapkey(continued) ~ Close `main_dlg_cur` `File.cb_file_erase`;\
mapkey(continued) ~ Activate `main_dlg_cur` `psh_erase_not_disp`;\
mapkey(continued) ~ Select `file_erase_nd` `Filelist`0 ;~ Activate `file_erase_nd` `ok_pb`;
mapkey a @MAPKEY_LABEL实体;~ Activate `main_dlg_cur` `ProCmdModelNew.file`;\
1 v' a+ x/ x2 L1 Cmapkey(continued) ~ Activate `new` `chk_use_default_template`0 ;~ Activate `new` `OK`;\
6 N9 @  ~1 O+ u  Lmapkey(continued) ~ FocusIn `new_file_opts` `psh_ok`;~ Activate `new_file_opts` `psh_ok`;
* }$ N% T& O) e( Gmapkey z @MAPKEY_LABELdwg;~ Select `main_dlg_cur` `MenuBar1`1  `File`;\
mapkey(continued) ~ Close `main_dlg_cur` `MenuBar1`;\
; E0 `% h* ^3 \& i3 Zmapkey(continued) ~ Activate `main_dlg_cur` `File.psh_save_as`;\
2 G; a( f) z( g8 M: Fmapkey(continued) ~ Select `file_saveas` `ph_list.Filelist`1  `DWG`;\
mapkey(continued) ~ Activate `file_saveas` `ph_list.Filelist`1  `DWG`;\
mapkey(continued) ~ Open `file_saveas` `type_option`;~ Close `file_saveas` `type_option`;\
3 h8 \  L. }; ^; umapkey(continued) ~ Select `file_saveas` `type_option`1  `db_560`;
  C+ X' f7 N2 {1 D. Wmapkey a @MAPKEY_LABEL实体;~ Activate `main_dlg_cur` `ProCmdModelNew.file`;\
. E+ z! e, X$ C2 ^mapkey(continued) ~ Activate `new` `chk_use_default_template`0 ;~ Activate `new` `OK`;\
2 B# F6 X. h; Y5 K# w- c% i. Bmapkey(continued) ~ FocusIn `new_file_opts` `psh_ok`;~ Activate `new_file_opts` `psh_ok`;
use_pre_wildfire_text_font yes
! `  n3 i4 _  p2 L7 @$ x& e5 Xtrail_dir D:\lcsing
plotter_command windows_print_manager
; {% L- V8 Q9 ~/ J* I7 r! g! Yedge_display_quality very_high
7 X3 m' O: L* w0 c) y$ Bintf2d_fit_incompatible_data yes
intf2d_out_acad_mtext yes
6 i; X% V3 U: \+ o8 @9 sintf2d_out_pnt_ent yes
# z1 Y' d0 L, H  tintf2d_out_enhanced_ents hatch_only
dxf_out_drawing_scale yes
" [1 [3 L, v" K4 isystem_colors_file D:\Program Files\proeWildfire 5.0\text\syscol.scl
) e# v) x) F6 X' {autobuildz_enabled yes
0 D4 t( r, P( `3 k+ B) L4 Imapkey d @MAPKEY_LABEL绘图;~ Command `ProCmdModelNew` ;\
  N/ A/ V; m; D, y- w% Bmapkey(continued) ~ Select `new` `Type`1  `Drawing`;\
mapkey(continued) ~ Activate `new` `chk_use_default_template`0 ;~ Activate `new` `OK`;\
mapkey(continued) ~ Select `dwg_create` `rad_format`1  `1`;\
+ J) w+ p( b( }4 K. c& Tmapkey(continued) ~ Activate `dwg_create` `psh_browse`;\
( z" d4 @  H/ D, e3 Z" cmapkey(continued) ~ Select `file_open` `Ph_list.Filelist`1  `qcmb.drw`;\
mapkey(continued) ~ Activate `file_open` `Open`;~ Activate `dwg_create` `psh_ok`;\
mapkey(continued) ~ Select `main_dlg_cur` `PHTLeft.PHLayerUI.AssyTree`1  \
+ q7 r% }% ~/ k  Y. ?4 ymapkey(continued) `node0:01___PRT_ALL_DTM_PLN`;\
& O& @' b0 {! fmapkey(continued) ~ Select `main_dlg_cur` `PHTLeft.PHLayerUI.AssyTree`1  \
mapkey(continued) `node0:01___PRT_ALL_DTM_PLN`;
4 q, f5 _0 O' l! |" ]mapkey d @MAPKEY_LABEL绘图;~ Command `ProCmdModelNew` ;\
mapkey(continued) ~ Select `new` `Type`1  `Drawing`;\
mapkey(continued) ~ Activate `new` `chk_use_default_template`0 ;~ Activate `new` `OK`;\
mapkey(continued) ~ Select `dwg_create` `rad_format`1  `1`;\
# ~: `' ]2 p) w% Pmapkey(continued) ~ Activate `dwg_create` `psh_browse`;\
# H" ?0 J1 e5 }1 x( T9 C6 ?( Ymapkey(continued) ~ Select `file_open` `Ph_list.Filelist`1  `qcmb.drw`;\
mapkey(continued) ~ Activate `file_open` `Ph_list.Filelist`1  `qcmb.drw`;\
9 X' |  m5 f$ Q* tmapkey(continued) ~ Activate `dwg_create` `psh_ok`;
: ?0 D3 u. g6 F6 o+ j5 xaccuracy_lower_bound 1e-04
enable_absolute_accuracy yes
save_model_display shading_lod
save_texture_with_model yes
% I- O* {! @1 E5 @" t4 P2 Ostep_appearance_layers_groups yes
% N3 M, b# M# F2 h- t& \  Adefault_ang_dec_places 2
! ?2 R4 ?1 w8 d! ^# ?. V0 f1 a# {default_dec_places 2
7 B9 X3 l5 ]; r0 a* \info_output_format text
9 L9 m% o; c, x2 j8 kdisplay shade
spin_center_display no
6 ]0 f& h* w/ }2 ]display_planes yes
dwg_export_format 14
* c( M# T6 }$ U# Uinterface_quality 3
" l- k2 F7 s$ p# l, o$ Xtol_mode nominal
& W7 [& S, I/ B4 d$ Tsave_drawing_picture_file embed
auto_regen_views yes
flip_arrow_scale 1
visible_message_lines 2
$ L3 n) U$ I6 H$ u5 [display_full_object_path yes
web_browser_history_days 0
regen_backup_using_disk yes
clock no
emplate_drawing a4_drawing.drw
! j* {+ F' k1 P! @% ?" W  }help_translation yes
1 B$ p5 m! F) Amsg_translation yes
) g# \7 f  D. l' jdialog_translation yes
/ c% j4 s* @% u; P4 jregen_backup_directory D:\lcsing

* l4 O7 V5 A( o% d. g7 i[ 本帖最后由 boylcx 于 2009-12-2 16:06 编辑 ]

boylcx

绘图选项
$ U$ k! O% H3 r/ r" a' wdrawing_text_height 2.5
4 u6 y5 s/ d  X( mtext_thickness 0.000000
; b, J1 `: t6 p6 Ztext_width_factor 0.8
5 C) J( h* m+ o7 l( haux_view_note_format VIEW %viewname-%viewname
& b9 `" z( W' k% a( l- U3 Rbroken_view_offset 1.000000
- z: {/ V& |+ F2 l/ d4 f" t7 hcreate_area_unfold_segmented YES
3 O( ?) e' V. C  I2 x  Udef_view_text_height 0.000000
9 Y" I0 j1 X% ldef_view_text_thickness 0.000000
, h: P! D7 z0 Ydefault_view_label_placement BOTTOM_LEFT
/ d' y2 l' y1 c" @0 J: zdetail_circle_line_style SOLIDFONT
) P, u* U" A' W) Z" ~1 cdetail_circle_note_text DEFAULT
$ \7 z2 L- b  c5 Y; ~# x! p) fdetail_view_boundary_type CIRCLE
detail_view_circle ON
! s6 ~+ s* A' s; f% i- gdetail_view_scale_factor 2.000000
half_view_line SOLID
model_display_for_new_views FOLLOW_ENVIRONMENT
  Q  @1 @) P( I3 F' `projection_type THIRD_ANGLE
show_total_unfold_seam YES
6 Z# A7 t2 g# b% Stan_edge_display_for_new_views DEFAULT
view_note STD_ANSI
+ N) a- k& F4 X( Pview_scale_denominator 100
+ d% z" o( n9 p% N2 fview_scale_format ratio_colon
4 R* n! N# Q3 z. d& Tcrossec_arrow_length 3.000000
crossec_arrow_style TAIL_ONLINE
crossec_arrow_width 1.000000
; Q/ d6 H! |( \9 Y9 ^! I% }crossec_text_place AFTER_HEAD
- X6 u2 f& `) T+ h" ?crossec_type OLD_STYLE
cutting_line STD_ANSI
4 @9 \# h. T4 Pcutting_line_adapt NO
* z. k) `: Y0 D; B3 i1 b4 acutting_line_segment 0.000000
def_xhatch_break_around_text NO
def_xhatch_break_margin_size 0.150000
1 N: s/ A+ ^: @: h+ I* m4 ydefault_show_2d_section_xhatch ASSEMBLY_AND_PART
" s# R+ M6 m' h3 j1 w! ~% T. Jdefault_show_3d_section_xhatch NO
draw_cosms_in_area_xsec NO
remove_cosms_from_xsecs TOTAL
show_quilts_in_total_xsecs NO
datum_point_shape CROSS
datum_point_size 0.312500
/ W, ]$ [" w8 S" s7 [) C2 rhidden_tangent_edges DEFAULT
# g; K) y+ u- ~hlr_for_datum_curves YES
hlr_for_pipe_solid_cl NO
- Q7 k6 Q. U2 A) r9 ~6 Yhlr_for_threads YES
! y2 v! @7 a' n; nlocation_radius DEFAULT(2.)
mesh_surface_lines ON
pipe_insulation_solid_xsec NO
ref_des_display NO
show_sym_of_suppressed_weld NO
+ k8 j" r! o! uthread_standard STD_ANSI
2 P8 X( h  X2 P# R+ h- Dweld_light_xsec NO
weld_solid_xsec NO
allow_3d_dimensions NO
angdim_text_orientation HORIZONTAL
associative_dimensioning YES
/ W8 J: ~: N+ O6 C6 H) nchamfer_45deg_leader_style STD_ASME_ANSI
chamfer_45deg_dim_text JIS
: A( a3 ]1 L/ J* J0 cclip_diam_dimensions YES
' P6 e7 v: x5 T. ^clip_dimensions YES
  T  n! F  y0 `! P1 z: cclip_dim_arrow_style DOUBLE_ARROW
" E" D( L3 U4 H1 I2 gdefault_dim_elbows YES
default_z_radius_center_symbol CROSS
dim_fraction_format DEFAULT
dim_leader_length 10.000000
* S. q- Q( @' x; |; P$ L/ }dim_text_gap 0.500000
* z6 i7 K& \' M% K- F2 bdim_trail_zero_max_places same_as_dim
draft_scale 1.000000
7 h1 n* Q7 g& p: a* l; ydraw_ang_units ANG_DEG
5 s4 \3 c4 s- p2 ~+ jdraw_ang_unit_trail_zeros YES
2 _' W' |3 }* O7 Bdual_digits_diff -1
dual_dimensioning NO
dual_dimension_brackets YES
7 U: V/ g+ m: m, X! \8 Z, `9 W& jdual_metric_dim_show_fractions NO
$ Y& u5 w% Z6 ]dual_secondary_units MM
iso_ordinate_delta NO
lead_trail_zeros STD_DEFAULT
lead_trail_zeros_scope DIMS
orddim_text_orientation PARALLEL
ord_dim_standard STD_ANSI
! g" [; U9 N$ j/ P2 B% ?parallel_dim_placement ABOVE
; y: U; z4 b7 J, j2 C+ @+ @radial_dimension_display STD_ASME
1 R2 b2 x9 T) jshrinkage_value_display PERCENT_SHRINK
) E3 z+ q+ d6 \5 {& v$ dtext_orientation PARALLEL_DIAM_HORIZ
. N) a/ Y$ K* ]7 B7 Cuse_major_units NO
witness_line_delta 3.000000
& i- ^! N* ?; C# E' ~& ?witness_line_intersection NO
witness_line_offset 0.062500
& C+ Y/ H, A0 D% ~" \default_clean_dim_offset 10.000000
default_clean_dim_increment 5.000000
default_font font
dim_dot_box_style DEFAULT
8 o% H) ^4 e# o( I* k# ~, s* Qdraw_arrow_length 3.000000
draw_arrow_style CLOSED
draw_arrow_width 1.000000
draw_attach_sym_height DEFAULT
5 `. M& Q; g- ~; bdraw_attach_sym_width DEFAULT
draw_dot_diameter DEFAULT
leader_elbow_length 0.250000
3 m. ]/ L+ j, B% F% Qleader_extension_font SOLIDFONT
+ k* ^) g+ j0 K  @3 _( Uset_datum_leader_length 0.000000
2 C9 N% I  o! s$ Iaxis_interior_clipping NO
axis_line_offset 3.000000
circle_axis_offset 3.000000
; E0 F* H% b; u! F! h- {radial_pattern_axis_circle NO
; a7 m6 p* w! b6 L6 }6 q( Vasme_dtm_on_dia_dim_gtol ON_GTOL
gtol_datum_placement_default ON_BOTTOM
gtol_datums STD_ANSI
gtol_dim_placement ON_BOTTOM
gtol_display_style STD
( X4 a9 X/ m2 W1 O+ l: F& A' ggtol_lead_trail_zeros SAME_AS_LEAD_TRAIL_ZEROS
new_iso_set_datums YES
6 w7 p$ s5 O  w3 b2 Pset_datum_triangle_display FILLED
stacked_gtol_align YES
* z1 L; ?* B/ R# L% d" E& x( }2d_region_columns_fit_text NO
  W+ t! o1 B, Z! m4 x+ T9 i  n4 d$ Odash_supp_dims_in_region YES
def_bom_balloons_attachment EDGE
$ f1 e( m0 Q: Ndef_bom_balloons_snap_lines NO
0 ]- w( C+ S; O0 \2 Ddef_bom_balloons_stagger NO
: H, n5 |. _( u  G7 vdef_bom_balloons_stagger_value 0.600000
; ?( }$ V: t- K# y; u1 G( Ddef_bom_balloons_view_offset 0.800000
( c4 J& Z# u# H# c) `, w& bdef_bom_balloons_edge_att_sym ARROWHEAD
. _' w+ e2 u, q. y3 \5 zdef_bom_balloons_surf_att_sym INTEGRAL
, U4 I; g: ?( U) ymin_dist_between_bom_balloons 0.800000
4 ?* D% h! ~& F, B- \1 P8 \( Smodel_digits_in_region YES
$ J( h# L0 g. g4 n5 R  x! ]8 _reference_bom_balloon_text "DEFAULT"
show_cbl_term_in_region YES
show_dim_sign_in_tables NO
sort_method_in_region DELIMITED
zero_quantity_cell_format EMPTY
draw_layer_overrides_model NO
4 s3 |9 B$ L6 t& i- z" Z, d0 mignore_model_layer_status YES
model_grid_balloon_display YES
; I$ u! u6 ?. H: ymodel_grid_balloon_size 0.200000
( d  |0 ~+ i. ~+ pmodel_grid_neg_prefix -
" F/ b  q' w1 _4 f. E& cmodel_grid_num_dig_display 0
model_grid_offset DEFAULT
model_grid_text_orientation HORIZONTAL
model_grid_text_position CENTERED
) A2 Y: Y  }& n* ~7 [9 F: Spipe_pt_line_style DEFAULT
pipe_pt_shape CROSS
pipe_pt_size DEFAULT
show_pipe_theor_cl_pts BEND_CL
& U8 M( J5 N, R, n5 Ublank_zero_tolerance NO
dim_tol_lead_trail_zeros SAME_AS_LEAD_TRAIL_ZEROS
$ I9 b9 O' N4 Y7 z) V1 ]dim_tol_trail_zero_max_places same_as_dim_tol
display_tol_by_1000 NO
" A! N0 s5 x3 n9 o1 \9 ]symmetric_tol_display_standard STD_ASME
tol_display NO
tol_text_height_factor STANDARD
tol_text_width_factor STANDARD
5 m( p0 ~+ V% sdecimal_marker COMMA_FOR_METRIC_DUAL
default_pipe_bend_note NO
drawing_units MM
harn_tang_line_display NO
) G( l0 n; t: c8 G; {* Y4 N, r" Iline_style_standard STD_ANSI
max_balloon_radius 0.000000
! m) R3 c4 Z( [* |min_balloon_radius 0.000000
7 y- R) c# J2 {- h- w$ ~node_radius DEFAULT
2 V1 l& g  N6 f7 qpos_loc_format %s%x%y, %r
" B% ]' F: L; {$ K+ x" wsym_flip_rotated_text NO
! t7 j/ c2 |% L  A: D; _weld_symbol_standard STD_ANSI
. Z- z1 Z* W; z' U+ L4 ~weld_spot_side_significant YES
yes_no_parameter_display TRUE_FALSE

szzhaoj

你用了工程图模板没有？用模板的话好像就只认创建模板时指定的dtl

boylcx

用了，自己做的，里面有bom表和一些参数！
和工程模板有关关系吗？详细说下，谢谢！在线等待：QQ:123008118

zorro2

楼主，看看你的配置文件
& t% E8 P; h6 k: M( O5 V$ b$ |9 \drawing_setup_file D:\Program Files\proeWildfire 5.0\text\prodetail.dtl，
你的dtl文件是这个吗？如果不是换成你自己的。

boylcx

原帖由 szzhaoj 于 2009-12-2 16:13 发表 http://www.3dportal.cn/discuz/images/common/back.gif
% y/ L) v/ [. ^# P你用了工程图模板没有？用模板的话好像就只认创建模板时指定的dtl

7 H  V9 K4 u4 [" D0 [! {. T% X% m
, [' y% c) ?! [1 W3 ?4 r- p% a2 O% P问题已解决，是工程模板的问题，我用的是从CAD转到proe下的模板，不知那里搞错了！
用proe重新做了一个，问题就解决了！谢谢，谢谢你的提醒，谢谢大家的帮助！