| ASME 3977-1 | 2000年1月 | Gas turbines - Procurement - Part 1: General introduction and definitions |
| ASME 3977-2 | 2000年1月 | Gas turbines - Procurement - Part 2: Standard reference conditions and ratings |
| ASME A13.1*ANSI A 13.1 | 1996年1月 | Scheme for the identification of piping systems |
| ASME A17 | 2005年1月 | Elevator Code Cd Rom Registration Card |
| ASME A17 Checklist 1 | 1993年1月 | Checklist for inspection of electric elevators |
| ASME A17 Interpretations | 1979年1月 | Interpretations: A17 Documents 1972-1979 |
| ASME A17 Interpretations 2-13 | 1989年1月 | Interpretations Nos. 2-13: A17 Elevator and escalator committee June 1979 - May 1989 |
| ASME A17.1*CSA B44 | 2004年1月 | Safety Code for Elevators and Escalators |
| ASME A17.1 Handbook | 1993年1月 | Handbook: Safety code for elevators and escalators |
| ASME A17.2 | 2004年1月 | Guide for Inspection of Elevators, Escalators, and Moving Walks |
| ASME A17.3 | 2005年1月 | Safety Code for Existing Elevators and Escalators |
| ASME A17.4 | 1999年1月 | Guide for Emergency Personnel (Includes Evacuation Procedures and Firefighters' Service Operating Procedures) |
| ASME A17.5/B44.1 | 2004年1月 | Elevator and Escalator Electrical Equipment |
| ASME A18.1 | 2005年1月 | Safety Standard for Platform Lifts and Stairway Chairlifts |
| ASME A90.1 | 2003年1月 | Safety Standard for Belt Manlifts |
| ASME A112.1.2 | 2004年1月 | Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors) |
| ASME A112.1.3*ANSI A 112.1.3 | 2000年1月 | Air gap fittings for use with plumbing fixtures, appliances, and appurtenances |
| ASME A112.3.1*ANSI A 112.3.1 | 1993年1月 | Performance standard and installation procedures for stainless steel drainage systems for sanitary, storm, and chemical applications, above and below ground |
| ASME A112.3.4*ANSI A 112.3.4 | 2000年1月 | Macerating toilet systems and related components |
| ASME A112.4.1 | 1993年1月 | Water heater relief valve drain tubes |
| ASME A112.4.2 | 2003年1月 | Water Closet Personal Hygiene Devices |
| ASME A112.4.3 | 1999年1月 | Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System |
| ASME A112.4.7 | 2002年1月 | Point of Use and Branch Water Submetering Systems |
| ASME A112.4.14 | 2004年1月 | Manually Operated Quarter-Turn Shutoff Valves for Use in Plumbing Systems |
| ASME A112.6.1M | 1997年1月 | Floor-affixed supports for off-the-floor plumbing fixtures for public use / Note: Reconfirmed in 2002 |
| ASME A112.6.2 | 2001年1月 | Framing-Affixed Supports For The Off-The-Floor Water Closets With Concealed Tanks. |
| ASME A112.6.3 | 2001年1月 | Floor and trench drains |
| ASME A112.6.4 | 2003年1月 | Roof, Deck, and Balcony Drains |
| ASME A112.6.7 | 2001年1月 | Enameled and Epoxy Coated Cast Iron and PVC Plastic Sanitary Floor Sinks |
| ASME A112.6.9 | 2005年1月 | Siphonic Roof Drains |
| ASME A112.9.7 | 2006年1月 | Whirlpool Bathtub Appliances |
| ASME A112.14.1 | 2003年1月 | Backwater Valves |
| ASME A112.14.3 | 2000年1月 | Grease Interceptors |
| ASME A112.14.4 | 2001年1月 | Grease removal devices |
| ASME A112.14.6 | 2006年1月 | FOG (Fats, Oils, and Greases) Disposal Systems |
| ASME A112.18.1 | 2005年1月 | Plumbing Supply Fittings |
| ASME A112.18.2 | 2005年1月 | Plumbing Waste Fittings |
| ASME A112.18.3 | 2002年1月 | Performance requirements for backflow protection devices and systems in plumbing fixture fittings |
| ASME A112.18.6 | 2003年1月 | Flexible Water Connectors |
| ASME A112.18.7*ANSI A 112.18.7 | 1999年1月 | Deck mounted bath/shower transfer valves with integral backflow protection |
| ASME A112.19.1M*ANSI A 112.19.1M | 1994年1月 | Enameled cast iron plumbing fixtures |
| ASME A112.19.1M Errata | 1996年1月 | Enameled cast iron plumbing fixtures; Errata |
| ASME A112.19.1M Supplement 1*ANSI A 112.19.1M Supplement 1 | 1998年1月 | Enameled cast iron plumbing fixtures; Supplement 1 |
| ASME A112.19.1M Supplement 2*ANSI A 112.19.1M Supplement 2 | 2000年1月 | Enameled cast iron plumbing fixtures - Supplement 2 |
| ASME A112.19.2 | 2003年1月 | Vitreous China Plumbing Fixtures and Hydraulic Requirements for Water Closets and Urinals |
| ASME A112.19.3 | 2001年1月 | Stainless Steel Plumbing Fixtures (Designed for Residential Use) |
| ASME A112.19.3 Supplement 1 | 2002年1月 | Stainless steel plumbing fixtures (designed for residential use); Supplement 1 |
| ASME A112.19.4M*ANSI A 112.19.4M | 1994年1月 | Porcelain enameled formed steel plumbing fixtures |
| ASME A112.19.4M Errata | 1996年1月 | Porcelain enameled formed steel plumbing fixtures; Errata |
| ASME A112.19.4M Supplement 1*ANSI A 112.19.4M Supplement 1 | 1998年1月 | Porcelain enameled formed steel plumbing fixtures; Supplement 1 |
| ASME A112.19.4M Supplement 2*ANSI A 112.19.4M Supplement 2 | 2000年1月 | Porcelain enameled formed steel plumbing fixtures - Supplement 2 |
| ASME A112.19.5 | 2005年1月 | Trim for Water-Closet Bowls, Tanks, and Urinals |
| ASME A112.19.6 | 1995年1月 | Hydraulic performance requirements for water closets and urinals |
| ASME A112.19.7 | 2006年1月 | Hydromassage Bathtub Appliances |
| ASME A112.19.8M*ANSI A 112.19.8M | 1987年1月 | Suction fittings for use in swimming pools, wading pools, spas, hot tubs, and whirlpool bathtub appliances |
| ASME A112.19.9M | 1991年1月 | Non-vitreous ceramic plumbing fixtures |
| ASME A112.19.9M Supplement 1 | 2002年1月 | Non-vitreous ceramic plumbing fixtures; Supplement 1 |
| ASME A112.19.10 | 2003年1月 | Dual Flush Devices for Water Closets |
| ASME A112.19.12 | 2006年1月 | Wall Mounted And Pedestal Mounted, Adjustable And Pivoting Lavatory And Sink Carrier Systems |
| ASME A112.19.13 | 2002年1月 | Electrohydraulic Water Closets |
| ASME A112.19.14 | 2006年1月 | Six-Liter Water Closets Equipped with a Dual Flushing Device |
| ASME A112.19.15 | 2005年1月 | Bathtubs/Whirlpool Bathtubs with Pressure Sealed Doors |
| ASME A112.19.16 | 2006年1月 | Terrazzo Plumbing Fixtures |
| ASME A112.19.17 | 2002年1月 | Manufactured safety vacuum release systems (SVRS) for residential and commercial swimming pools, spa, hot tub, and wading pool suction systems |
| ASME A112.19.19 | 2006年1月 | Vitreous China Nonwater Urinals |
| ASME A112.20.1 | 2004年1月 | Qualification of Installers of High Purity Piping Systems |
| ASME A112.20.2 | 2004年1月 | Qualification of Installers of Firestop Systems and Devices for Piping Systems |
| ASME A112.21.3M*ANSI A 112.21.3M | 1985年1月 | Hydrants for utility and maintenance use |
| ASME A112.36.2M | 1991年1月 | Cleanouts |
| ASME A120.1 | 2006年1月 | Safety Requirements for Powered Platforms and Traveling Ladders and Gantries for Building Maintenance |
| ASME AG-1 | 2003年1月 | Code on Nuclear Air and Gas Treatment |
| ASME AS-11 | 2002年1月 | Personnel of Codes, Standards, and Related Conformity Assessment Committees |
| ASME B1/TR | 1993年1月 | Measurement uncertainty for 60 deg. screw thread gage element measurement (inch and metric) |
| ASME B1.1 | 2003年1月 | Unified Inch Screw Threads, UN and UNR Thread Form |
| ASME B1.2*ANSI B 1.2 | 1983年1月 | Gages and gaging for unified inch screw threads |
| ASME B1.2 Errata*ANSI B 1.2 Errata | 1992年1月 | Gages and gaging for unified inch screw threads; Errata |
| ASME B1.3M*ANSI B 1.3M | 1992年1月 | Screw thread gaging systems for dimensional acceptability - Inch and metric screw threads (UN, UNR, UNJ, M, and MJ) |
| ASME B1.3M Errata*ANSI B 1.3M Errata | 1994年1月 | Screw thread gaging systems for dimensional acceptability - Inch and metric screw threads (UN, UNR, UNJ, M, and MJ); Errata |
| ASME B1.5 | 1997年1月 | Acme screw threads / Note: Withdrawn by mistake |
| ASME B1.7 | 2006年1月 | Screw Threads: Nomenclature, Definitions, and Letter Symbols |
| ASME B1.8*ANSI B 1.8 | 1988年1月 | Stub Acme screw threads |
| ASME B1.9*ANSI B 1.9 | 1973年1月 | Buttress inch screw threads 7?45?form with 0.6 pitch basic height of thread engagement |
| ASME B1.10M | 2004年1月 | Unified Miniature Screw Threads |
| ASME B1.11*ANSI B 1.11*ASA B 1.11 | 1958年1月 | Microscope objective thread |
| ASME B1.12M*ANSI B 1.12 | 1987年1月 | Class 5 interference-fit thread |
| ASME B1.13M | 2005年1月 | Metric Screw Threads: M Profile |
| ASME B1.15 | 1995年1月 | Unified inch screw threads (UNJ thread form) |
| ASME B1.15 Errata | 1997年1月 | Unified inch screw threads (UNJ thread form) |
| ASME B1.16M*ANSI B 1.16M | 1984年1月 | Gages and gaging for metric M screw threads |
| ASME B1.20.1*ANSI B 1.20.1 | 1983年1月 | Pipe threads, general purpose (inch) |
| ASME B1.20.3*ANSI B 1.20.3 | 1976年1月 | Dryseal pipe threads (inch) |
| ASME B1.20.5*ANSI B 1.20.5 | 1991年1月 | Gaging for dryseal pipe threads (inch) |
| ASME B1.20.7*ANSI B 1.20.7 | 1991年1月 | Hose coupling screw threads (inch) |
| ASME B1.21M | 1997年1月 | Metric screw threads: MJ profile |
| ASME B1.22M*ANSI B 1.22M | 1985年1月 | Gages and gaging for MJ series metric screw threads |
| ASME B1.30 | 2002年1月 | Screw threads - Standard practice for calculating and rounding dimensions |
| ASME B4.1*USAS B 4.1 | 1967年1月 | Preferred limits and fits for cylindrical parts |
| ASME B4.2*ANSI B 4.2 | 1978年1月 | Preferred metric limits and fits |
| ASME B4.3*ANSI B 4.3 | 1978年1月 | General tolerances for metric dimensioned products |
| ASME B5.1M*ANSI B 5.1M | 1985年1月 | T-slots, their bolts, nuts, and tongues |
| ASME B5.8 | 2001年1月 | Chuck and Chuck Jaws |
| ASME B5.9*USAS B 5.9 | 1967年1月 | Spindle noses for tool room lathes, engine lathes, turret lathes, and automatic lathes |
| ASME B5.10*ANSI B 5.10 | 1994年1月 | Machine tapers - Self holding and steep taper series |
| ASME B5.11*ASA B 5.11 | 1964年1月 | Spindle noses and adjustable adapters for multiple spindle drilling heads |
| ASME B5.18*ANSI B 5.18 | 1972年1月 | Spindle noses and tool shanks for milling machines |
| ASME B5.25M*ANSI B 5.25M | 1980年1月 | Punch and die sets (metric) |
| ASME B5.28*ANSI B 5.28 | 1971年1月 | Mounting dimensions of lubricating and coolant pumps for machine tools |
| ASME B5.35*ANSI B 5.35 | 1983年1月 | Machine mounting specifications for abrasive discs and plate mounted wheels |
| ASME B5.35 Errata*ANSI B 5.35 Errata | 1985年1月 | Machine mounting specifications for abrasive discs and plate mounted wheels; Errata |
| ASME B5.40*ANSI B 5.40 | 1977年1月 | Spindle noses and tool shanks for horizontal boring machines |
| ASME B5.47*ANSI B 5.47 | 1972年1月 | Milling machine arbor assemblies |
| ASME B5.48*ANSI B 5.48 | 1977年1月 | Ball screws |
| ASME B5.48 Errata*ANSI B 5.48 Errata | 1979年1月 | Ball screws; Errata |
| ASME B5.49 | 1998年1月 | Glossary Of Power Press Terms |
| ASME B5.50*ANSI B 5.50 | 1994年1月 | V" flange tool shanks for machining centers with automatic tool changers" |
| ASME B5.50 Errata | 1995年1月 | V" flange tool shanks for machining centers with automatic tool changers |
| ASME B5.51M*ANSI B 5.51M | 1979年1月 | Preferred SI units for machine tools |
| ASME B5.52 | 2003年1月 | Power Presses: General Purpose, Single-Point Gap Type |
| ASME B5.53M*ANSI B 5.53M | 1982年1月 | Cutter and tool grinding machines |
| ASME B5.54 | 2005年1月 | Methods for Performance Evaluation of Computer Numerically Controlled Machining Centers |
| ASME B5.55M | 1994年1月 | Specification and performance standard, power press brakes |
| ASME B5.56M | 1994年1月 | Specification and performance standard, power shears |
| ASME B5.57 | 2000年1月 | Methods For Performance Evaluation Of Computer Numerically Controlled Lathes And Turning Centers |
| ASME B5.60 | 2002年1月 | Workholding Chucks: Jaw Type Chucks |
| ASME B5.61 | 2003年1月 | Power Presses: General Purpose, Single-Action, Straight Side Type |
| ASME B15.1*ANSI B 15.1 | 2000年1月 | Safety standard for mechanical power transmission apparatus |
| ASME B16.1 | 2005年1月 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASME B16.3 | 1998年1月 | Malleable iron threaded fittings; Classes 150 and 300 |
| ASME B16.4 | 1998年1月 | Gray iron threaded fittings; Classes 125 and 250 |
| ASME B16.5 | 2003年1月 | Pipe Flanges and Flanged Fittings: NPS 1/2 through 24 |
| ASME B16.9 | 2003年1月 | Factory-Made Wrought Buttwelding Fittings |
| ASME B16.10 | 2000年1月 | Face-to-face and end-to-end dimensions of valves / Note: Reconfirmed in 2003 |
| ASME B16.11 | 2005年1月 | Forged Fittings, Socket-Welding and Threaded |
| ASME B16.12 | 1998年1月 | Cast iron threaded drainage fittings |
| ASME B16.14*ANSI B 16.14 | 1991年1月 | Ferrous pipe plugs, bushings, and locknuts with pipe threads |
| ASME B16.15*ANSI B 16.15 | 1985年1月 | Cast bronze threaded fittings |
| ASME B16.18 | 2001年1月 | Cast copper alloy solder joint pressure fittings |
| ASME B16.20*ANSI B 16.20 | 1998年1月 | Metallic gaskets for pipe flanges - Ring-joint, spiral-wound, and jacketed / Note: Withdrawn by mistake |
| ASME B16.20a Addenda*ANSI B 16.20a Addenda | 2000年1月 | Metallic gaskets for pipe flanges - Ring-joint, spiral-wound, and jacketed; Addenda |
| ASME B16.21 | 2005年1月 | Nonmetallic Flat Gaskets for Pipe Flanges |
| ASME B16.22 | 2001年1月 | Wrought copper and copper alloy solder joint pressure fittings |
| ASME B16.23 | 2002年1月 | Cast copper alloy solder joint drainage fittings: DWV |
| ASME B16.23 Errata | 2003年1月 | Cast copper alloy solder joint drainage fittings - DWV; Errata |
| ASME B16.24 | 2001年1月 | Cast copper alloy pipe flanges and flanged fittings: Classes 150, 300, 400, 600, 900, 1500, and 2500 |
| ASME B16.25 | 2003年1月 | Buttwelding Ends |
| ASME B16.26 | 2006年1月 | Cast Copper Alloy Fittings for Flared Copper Tubes |
| ASME B16.28*ANSI B 16.28 | 1994年1月 | Wrought steel buttwelding short radius elbows and returns |
| ASME B16.29 | 2001年1月 | Wrought copper and wrought copper alloy solder joint drainage fittings - DWV |
| ASME B16.33 | 2002年1月 | Manually operated metallic gas valves for use in gas piping systems up to 125 psig (sizes NPS 1/2 through NPS 2) |
| ASME B16.34 | 2004年1月 | Valves Flanged, Threaded and Welding End |
| ASME B16.36*ANSI B 16.36 | 1996年1月 | Orifice flanges |
| ASME B16.38*ANSI B 16.38 | 1985年1月 | Large metallic valves for gas distribution (manually operated, NPS 2 1/2 to 12, 125 psig maximum) |
| ASME B16.39 | 1998年1月 | Malleable iron threaded pipe unions; Classes 150, 250, and 300 |
| ASME B16.40 | 2002年1月 | Manually operated thermoplastic gas shutoffs and valves in gas distribution systems |
| ASME B16.40 Erratum | 2003-07-00 | Manually operated thermoplastic gas shutoffs and valves in gas distribution systems; Erratum to ASME B16.40-2002 |
| ASME B16.42*ANSI B 16.42 | 1998年1月 | Ductile iron pipe flanges and flanged fittings - Classes 150 and 300 |
| ASME B16.44 | 2002年1月 | Manually Operated Metallic Gas Values for Use in Above Ground Piping Systems up to 5 psi |
| ASME B16.45 | 1998年1月 | Cast Iron Fittings For Sovent Drainage Systems |
| ASME B16.47*ANSI B 16.47 | 1996年1月 | Large diameter steel flanges - NPS 26 through NPS 60 |
| ASME B16.48 | 2005年1月 | Line Blanks |
| ASME B16.49*ANSI B 16.49 | 2000年1月 | Factory-made wrought steel buttwelding induction bends for transportation and distribution systems |
| ASME B16.50 | 2001年1月 | Wrought copper and copper alloy braze-joint pressure fittings |
| ASME B17.1*USAS B 17.1 | 1967年1月 | Keys and keyseats |
| ASME B17.2*USAS B 17.2 | 1967年1月 | Woodruff keys and keyseats |
| ASME B18.1.1*ANSI B 18.1.1 | 1972年1月 | Small solid rivets |
| ASME B18.1.2*ANSI B 18.1.2. | 1972年1月 | Large rivets |
| ASME B18.1.3M*ANSI B 18.1.3M | 1983年1月 | Metric small solid rivets |
| ASME B18.1.3M Errata*ANSI B 18.1.3M Errata | 1985年1月 | Metric small solid rivets; Errata |
| ASME B18.2.1*ANSI B 18.2.1 | 1996年1月 | Square and hex bolts and screws (Inch series) |
| ASME B18.2.1 Erratum | 2003-07-00 | Square and hex bolts and screws (Inch series); Erratum to ASME B18.2.1-1996 |
| ASME B18.2.1a Addenda*ANSI B 18.2.1a Addenda | 1999年1月 | Square and hex bolts and screws (inch series); Addenda |
| ASME B18.2.2*ANSI B 18.2.2 | 1987年1月 | Square and hex nuts (Inch series) |
| ASME B18.2.3.1M*ANSI B 18.2.3.1M | 1999年1月 | Metric hex cap screws |
| ASME B18.2.3.2M | 2005年1月 | Metric Formed Hex Screws |
| ASME B18.2.3.3M*ANSI B 18.2.3.3M | 1979年1月 | Metric heavy hex screws |
| ASME B18.2.3.3M Errata*ANSI B 18.2.3.3M Errata | 1981年1月 | Metric heavy hex screws; Errata |
| ASME B18.2.3.4M | 2001年1月 | Metric hex flange screws |
| ASME B18.2.3.5M*ANSI B 18.2.3.5M | 1979年1月 | Metric hex bolts |
| ASME B18.2.3.5M Errata*ANSI B 18.2.3.5M Errata | 1981年1月 | Metric hex bolts; Errata |
| ASME B18.2.3.6M*ANSI B 18.2.3.6M | 1979年1月 | Metric heavy hex bolts |
| ASME B18.2.3.6M Errata*ANSI B 18.2.3.6M Errata | 1981年1月 | Metric heavy hex bolts; Errata |
| ASME B18.2.3.7M*ANSI B 18.2.3.7M | 1979年1月 | Metric heavy hex structural bolts |
| ASME B18.2.3.7M Errata*ANSI B 18.2.3.7M Errata | 1981年1月 | Metric heavy hex structural bolts; Errata |
| ASME B18.2.3.8M*ANSI B 18.2.3.8M | 1981年1月 | Metric hex lag screws |
| ASME B18.2.3.9M | 2001年1月 | Metric heavy hex flange screws |
| ASME B18.2.3.10M | 1996年1月 | Square Head Bolts (Metric Series) |
| ASME B18.2.4.1M | 2002年1月 | Metric hex nuts, style 1 |
| ASME B18.2.4.2M | 2005年1月 | Metric Hex Nuts, Style 2 |
| ASME B18.2.4.3M*ANSI B 18.2.4.3M | 1979年1月 | Metric slotted hex nuts |
| ASME B18.2.4.3M Errata*ANSI B 18.2.4.3M Errata | 1981年1月 | Metric slotted hex nuts; Errata |
| ASME B18.2.4.4M*ANSI B 18.2.4.4M | 1982年1月 | Metric hex flange nuts |
| ASME B18.2.4.5M*ANSI B 18.2.4.5M | 1979年1月 | Metric hex jam nuts |
| ASME B18.2.4.5M Errata*ANSI B 18.2.4.5M Errata | 1981年1月 | Metric hex jam nuts; Errata |
| ASME B18.2.4.6M*ANSI B 18.2.4.6M | 1979年1月 | Metric heavy hex nuts |
| ASME B18.2.4.6M Errata*ANSI B 18.2.4.6M Errata | 1981年1月 | Metric heavy hex nuts; Errata |
| ASME B18.2.6 | 2006年1月 | Fasteners for use in Structural Applications |
| ASME B18.2.7.1M | 2002年1月 | Metric 12-spline flange screws |
| ASME B18.2.7.1M Erratum | 2002年1月 | Metric 12-spline flange screws; Erratum |
| ASME B18.2.8 | 1999年1月 | Clearance Holes For Bolts Screws And Studs |
| ASME B18.3 | 2003年1月 | Socket Cap, Shoulder, and Set Screws, Hex and Spline Keys (Inch Series) |
| ASME B18.3.1M*ANSI B 18.3.1M | 1986年1月 | Socket head cap screws (Metric series) |
| ASME B18.3.2M*ANSI B 18.3.2M | 1979年1月 | Metric series hexagon keys and bits |
| ASME B18.3.3M*ANSI B 18.3.3M | 1986年1月 | Hexagon socket head shoulder screws (Metric series) |
| ASME B18.3.4M*ANSI B 18.3.4M | 1986年1月 | Hexagon socket button head cap screws (Metric series) |
| ASME B18.3.5M*ANSI B 18.3.5M | 1986年1月 | Hexagon socket flat countersunk head cap screws (Metric series) |
| ASME B18.3.6M*ANSI B 18.3.6M | 1986年1月 | Metric series socket set screws |
| ASME B18.5*ANSI B 18.5 | 1990年1月 | Round head bolts (Inch series) |
| ASME B18.5.2.1M | 2006年1月 | Metric Round Head Short Square Neck Bolts |
| ASME B18.5.2.2M*ANSI B 18.5.2.2M | 1982年1月 | Metric round head square neck bolts |
| ASME B18.5.2.3M*ANSI B 18.5.2.3M | 1990年1月 | Round head square neck bolts with large head (Metric series) |
| ASME B18.6.1*ANSI B 18.6.1 | 1981年1月 | Wood screws (Inch series) |
| ASME B18.6.2 | 1998年1月 | Slotted head cap screws, square head set screws, and slotted headless set screws (Inch series) |
| ASME B18.6.3 | 2003年1月 | Machine Screws and Machine Screw Nuts |
| ASME B18.6.4 | 1999年1月 | Thread Forming And Thread Cutting Tapping Screws And Metallic Drive Screws, Inch Series |
| ASME B18.6.5M*ANSI B 18.6.5M | 2000年1月 | Metric thread-forming and thread-cutting tapping screws |
| ASME B18.6.7M*ANSI B 18.6.7M | 1999年1月 | Metric machine screws / Note: Withdrawn by mistake |
| ASME B18.7*ANSI B 18.7 | 1972年1月 | General purpose semi-tubular rivets, full tubular rivets, split rivets and rivet caps |
| ASME B18.7.1M*ANSI B 18.7.1M | 1984年1月 | Metric general purpose semi-tubular rivets |
| ASME B18.8.1*ANSI B 18.8.1 | 1994年1月 | Clevis pins and cotter pins (Inch series) |
| ASME B18.8.1 Errata | 1995年1月 | Clevis pins and cotter pins (Inch series); Errata |
| ASME B18.8.2 | 2000年1月 | Taper pins, dowel pins, straight pins, grooved pins, and spring pins (Inch series) |
| ASME B18.8.100M | 2001年1月 | Spring Pins: Coiled Type, Spring Pins: Slotted, Machine Dowel Pins: Hardened Ground, and Grooved Pins (Metric) / Note: This Standard is a consolidation of ASME B18.8.3M-2000, B18.8.4M-2000, B18.8.5M-2000, and B18.8.9M-2000 |
| ASME B18.8.200M*ANSI B 18.8.200M | 2000年1月 | Cotter pins, headless clevis pins, and headed clevis pins (Metric series) |
| ASME B18.9*ANSI B 18.9 | 1996年1月 | Plow bolts (inch series) |
| ASME B18.10 | 2006年1月 | Track Bolts and Nuts |
| ASME B18.11*ANSI B 18.11 | 1961年1月 | Miniature screws |
| ASME B18.12 | 2001年1月 | Glossary of terms for mechanical fasteners |
| ASME B18.13*ANSI B 18.13 | 1996年1月 | Screw and washer assemblies - SEMS (Inch series) |
| ASME B18.13.1M | 1999年1月 | Screw And Washer Assemblies-Sems (Metric Series) |
| ASME B18.15M | 1998年1月 | Metric Lifting Eyes |
| ASME B18.16M | 2004年1月 | Dimensional Requirements for Prevailing-Torque-Type Steel Metric Hex Nuts and Hex Flange Nuts |
| ASME B18.18.1M*ANSI B 18.18.1M | 1987年1月 | Inspection and quality assurance for general purpose fasteners |
| ASME B18.18.2M | 1994年1月 | Supplement to Inspection and Quality Assurance for High Volume Machine Assembly Fasteners |
| ASME B18.18.3M*ANSI B 18.18.3M | 1987年1月 | Inspection and quality assurance for special purpose fasteners |
| ASME B18.18.4M*ANSI B 18.18.4M | 1987年1月 | Inspection and quality assurance for fasteners for highly specialized engineered applications |
| ASME B18.18.5M | 1998年1月 | Inspection And Quality Assurance Plan Requiring In-Process Inspection And Control |
| ASME B18.18.6M | 1998年1月 | Quality Assurance Plan For Fasteners Produced In A Third Party Accreditation System |
| ASME B18.18.7M | 1998年1月 | Quality Assurance Plan For Fasteners Produced In A Customer Approved Control Plan |
| ASME B18.21.1*ANSI B 18.21.1 | 1999年1月 | Lock washers (Inch series) |
| ASME B18.21.2M*ANSI B 18.21.2M | 1999年1月 | Lock washers (Metric series) |
| ASME B18.22.1*ANSI B 18.22.1 | 1965年1月 | Plain washers |
| ASME B18.22M*ANSI B 18.22M | 1981年1月 | Metric plain washers |
| ASME B18.22M Errata*ANSI B 18.22M Errata | 1983年1月 | Metric plain washers; Errata |
| ASME B18.24 | 2004年1月 | Part Identifying Number (PIN) |
| ASME B18.25.1M*ANSI B 18.25.1M | 1996年1月 | Square and rectangular keys and keyways |
| ASME B18.25.2M*ANSI B 18.25.2M | 1996年1月 | Woodruff keys and keyways |
| ASME B18.25.3M | 1998年1月 | Square And Rect Keys And Keyways: Width Tolerances And Deviations Greater Than Basic Size |
| ASME B18.27 | 1999年1月 | Tapered And Reduced Cross Section Retaining Rings (Inch Series) |
| ASME B18.27b Addenda | 2000年1月 | Tapered and reduced cross section retaining rings (Inch series); Addenda |
| ASME B18.29.1*ANSI B 18.29.1 | 1993年1月 | Helical coil screw thread inserts - Free running and screw locking (Inchs series) |
| ASME B18.29.1 Errata*ANSI B 18.29.1 Errata | 1995年1月 | Helical coil screw thread inserts - Free running and screw locking (Inchs series) |
| ASME B18.29.2M | 2005年1月 | Helical Coil Screw Thread Inserts: Free Running and Screw Locking (Metric Series) |
| ASME B18.30.1M | 2000年1月 | Open-End Blind Rivets With Break Mandrels (Metric Series) |
| ASME B18.31.1M | 2005年1月 | Metric Continuous and Double End Studs |
| ASME B19.1*ANSI B 19.1 | 1995年1月 | Safety standard for air compressor systems |
| ASME B19.3*ANSI B 19.3 | 1991年1月 | Safety standard for compressors for process industries |
| ASME B19.3a Addenda*ANSI B 19.3a Addenda | 1994年1月 | Safety standard for compressors for process industries; Addenda |
| ASME B19.3b Addenda*ANSI B 19.3b Addenda | 1995年1月 | Safety standard for compressors for process industries |
| ASME B20.1 | 2006年1月 | Safety Standard for Conveyors and Related Equipment |
| ASME B27.6*ANSI B 27.6 | 1972年1月 | General purpose uniform cross section spiral retaining rings |
| ASME B27.7*ANSI B 27.7 | 1977年1月 | General purpose tapered and reduced cross section retaining rings |
| ASME B27.8M*ANSI B 27.8M | 1978年1月 | General purpose metric tapered and reduced cross section retaining rings - Type 3DM1: Heavy duty external rings - Type 3EM1: Reinforced E" rings - Type 3FM1: "C" type rings" |
| ASME B29.2M*ANSI B 29.2M | 1982年1月 | Inverted tooth (silent) chains and sprockets |
| ASME B29.2M Errata*ANSI B 29.2M Errata | 1985年1月 | Inverted tooth (silent) chains and sprockets; Errata |
| ASME B29.8 | 2002年1月 | Leaf Chains, Clevises and Sheaves |
| ASME B29.10M | 1997年1月 | Heavy Duty Offset Sidebar Power Transmission Roller Chains And Sprocket Teeth |
| ASME B29.12M*ANSI B 29.12M | 1997年1月 | Steel bushed rollerless chains, attachments, and sprocket teeth |
| ASME B29.15M | 1997年1月 | Steel Roller Type Conveyor Chains, Attachments, And Sprocket Teeth |
| ASME B29.17M | 1998年1月 | Hinge Type Flat Top Conveyor Chains and Sprocket Teeth |
| ASME B29.21M*ANSI B 29.21M | 1996年1月 | 700 class welded steel and cast chains, attachments and sprockets for water and sewage treatment plants |
| ASME B29.22 | 2001年1月 | Drop Forged Rivetless Chains, Sprocket Teeth Drive Chain/Drive Dogs |
| ASME B29.23M*ANSI B 29.23M | 1985年1月 | Flexible chain couplings |
| ASME B29.24 | 2002年1月 | Roller Load Chains for Overhead Hoists |
| ASME B29.26 | 2001年1月 | Fatigue testing - Power transmission roller chain |
| ASME B29.26 Errata | 2002年1月 | Fatigue testing - Power transmission roller chain; Errata |
| ASME B29.27 | 2002年1月 | Single Pitch and Double Pitch Hollow Pin Conveyor Chains and Attachments |
| ASME B29.100 | 2002年1月 | Precision power transmission, double-pitch power transmission, and double-pitch conveyor roller chains, attachments, and sprockets |
| ASME B29.100 Erratum | 2004-01-00 | Precision power transmission, double-pitch power transmission, and double-pitch conveyor roller chains, attachments, and sprockets |
| ASME B29.200 | 2001年1月 | Welded-Steel-Type Mill Chains, Welded-Steel-Type Drag Chains, Attachments, and Srpocket Teeth |
| ASME B29.300*ANSI B 29.300 | 1998年1月 | Agricultural, detachable, and pintle chains, attachments, and sprockets |
| ASME B29.300a Addenda | 2004年1月 | Agricultural, detachable, and pintle chains, attachments, and sprockets |
| ASME B29.400 | 2001年1月 | Combination, H" Type Mill Chains, and Sprockets" |
| ASME B30.1 | 2004年1月 | Jacks |
| ASME B30.2 | 2005年1月 | Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist) |
| ASME B30.3 | 2004年1月 | Construction Tower Cranes |
| ASME B30.4 | 2003年1月 | Portal, tower, and pedestal cranes |
| ASME B30.5 | 2004年1月 | Mobile and Locomotive Cranes |
| ASME B30.6 | 2003年1月 | Derricks |
| ASME B30.7 | 2001年1月 | Base-mounted drum hoists |
| ASME B30.8 | 2004年1月 | Floating Cranes and Floating Derricks |
| ASME B30.9 | 2003年1月 | Slings |
| ASME B30.10 | 2005年1月 | Hooks |
| ASME B30.11 | 2004年1月 | Monorails and Underhung Cranes |
| ASME B30.12 | 2001年1月 | Handling Loads Suspended from Rotorcraft |
| ASME B30.13 | 2003年1月 | Storage/Retrieval (S/R) Machines and Associated Equipment |
| ASME B30.14 | 2004年1月 | Side Boom Tractors |
| ASME B30.16 | 2003年1月 | Overhead Hoists (Underhung) |
| ASME B30.17 | 2003年1月 | Overhead and gantry cranes (top running bridge, single girder, underhung hoist) |
| ASME B30.18 | 2004年1月 | Stacker Cranes (Top or Under Running Bridge, Multiple Girder with Top or Under Running Trolley Hoist) |
| ASME B30.19 | 2005年1月 | Cableways |
| ASME B30.20 | 2003年1月 | Below-the-Hook Lifting Devices |
| ASME B30.21 | 2005年1月 | Manually Lever Operated Hoists |
| ASME B30.22 | 2005年1月 | Articulating Boom Cranes |
| ASME B30.23 | 2005年1月 | Personnel Lifting Systems |
| ASME B30.25 | 2003年1月 | Scrap and Material Handlers |
| ASME B30.26 | 2004年1月 | Rigging Hardware |
| ASME B30.27 | 2005年1月 | Material Placement Systems |
| ASME B31.1 | 2007年1月 | Power Piping |
| ASME B31.2*USAS B 31.2 | 1968年1月 | Fuel gas piping |
| ASME B31.3 | 2006年1月 | Process Piping |
| ASME B31.4 | 2006年1月 | Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids |
| ASME B31.5 | 2001年1月 | Refrigeration piping and heat transfer components |
| ASME B31.8 | 2003年1月 | Gas Transmission and Distribution Piping Systems |
| ASME B31.8S | 2004年1月 | Managing System Integrity of Gas Pipelines |
| ASME B31.9 | 2004年1月 | Building Services Piping |
| ASME B31.11 | 2002年1月 | Slurry transportation piping systems |
| ASME B31G*ANSI B 31G | 1991年1月 | Manual for determining the remaining strength of corroded pipelines; A supplement to ASME B31 code for pressure piping |
| ASME B31Q | 2006年1月 | Pipeline Personnel Qualification |
| ASME B32.5*ANSI B 32.5 | 1977年1月 | Preferred metric sizes for tubular metal products other than pipe |
| ASME B32.100 | 2005年1月 | Preferred Metric Sizes for Flat, Round, Square, Rectangular and Hexangonal Metal Products |
| ASME B36.10M | 2004年1月 | Welded and Seamless Wrought Steel Pipe |
| ASME B36.19M | 2004年1月 | Stainless Steel Pipe |
| ASME B40.100 | 2005年1月 | Pressure Gauges and Gauge Attachments |
| ASME B40.200 | 2001年1月 | Thermometers, Direct Reading and Remote Reading / Note: Incorporating ASME B40.3, B40.4, and B40.9 |
| ASME B40.200a Addenda | 2003年1月 | Thermometers, Direct Reading and Remote Reading; Addenda |
| ASME B46.1 | 2002年1月 | Surface texture (surface roughness, waviness, and lay) |
| ASME B47.1*ANSI B 47.1 | 1988年1月 | Gage blanks |
| ASME B73.1 | 2001年1月 | Specification for horizontal end suction centrifugal pumps for chemical process |
| ASME B73.2 | 2003年1月 | Specifications for Vertical In-Line Centrifugal Pumps for Chemical Process |
| ASME B73.3 | 2003年1月 | Specification for Sealless Horizontal End Suction Metallic Centrifugal Pumps for Chemical Process |
| ASME B73.5M*ANSI B 73.5M | 1995年1月 | Specification for thermoplastic and thermoset polymer material horizontal end suction centrifugal pumps for chemical process |
| ASME B89/TP | 1990年1月 | Space plate test recommendations for coordinate measuring machines |
| ASME B89/TR | 1990年1月 | Parametric calibration of coordinate measuring machines |
| ASME B89.1.2M*ANSI B 89.1.2M | 1991年1月 | Calibration of gage blocks by contact comparison methods (through 20 in. and 500 mm) |
| ASME B89.1.5 | 1998年1月 | Measurement Of Plain External Diameters For Use As Master Discs Or Cylindrical Plug Gages |
| ASME B89.1.6 | 2002年1月 | Measurement of Plain Internal Diameters for Use as a Master Rings or Ring Guages |
| ASME B89.1.9 | 2002年1月 | Gage Blocks |
| ASME B89.1.10M | 2001年1月 | Dial Indicators (for Linear Measurement) |
| ASME B89.1.13 | 2001年1月 | Micrometers |
| ASME B89.1.17 | 2001年1月 | Measurement of thread measuring wires |
| ASME B89.3.1*ANSI B 89.3.1 | 1972年1月 | Measurement of out-of-roundness |
| ASME B89.3.4M*ANSI B 89.3.4M | 1985年1月 | Axes of rotation - Methods for specifying and testing |
| ASME B89.4.1*ANSI B 89.4.1 | 1997年1月 | Methods for performance evaluation of coordinate measuring machines |
| ASME B89.4.1a Addenda*ANSI B 89.4.1a Addenda | 1998年1月 | Methods for performance evaluation of coordinate measuring machines |
| ASME B89.4.1b Addenda | 2001年1月 | Methods for performance evaluation of coordinate measuring machines; Addenda |
| ASME B89.4.10 | 2000年1月 | Methods for Performance Evaluation of Coordinate Measuring System Software |
| ASME B89.4.19 | 2006年1月 | Performance Evaluation of Laser-Based Spherical Coordinate Measurement Systems |
| ASME B89.4.22 | 2004年1月 | Methods for Performance Evaluation of Articulated Arm Coordinate Measuring Machines |
| ASME B89.6.2*ANSI B 89.6.2 | 1973年1月 | Temperature and humidity environment for dimensional measurement |
| ASME B89.7.2*ANSI B 89.7.2 | 1999年1月 | Dimensional measurement planning |
| ASME B89.7.3.1 | 2001年1月 | Guidelines for decision rules: Considering measurement uncertainty in determining conformance to specifications |
| ASME B89.7.3.3 | 2002年1月 | Guidelines for Assessing the Reliability of Dimensional Measurement Uncertainty Statements |
| ASME B89.7.4.1 | 2005年1月 | Measurement Uncertainty and Conformance Testing: Risk Analysis (An ASME Technical Report) |
| ASME B89.7.5 | 2006年1月 | Metrological Traceability of Dimensional Measurements to the SI Unit of Length (An ASME Technical Report) |
| ASME B94.2*ANSI B 94.2 | 1995年1月 | Reamers |
| ASME B94.6*ANSI B 94.6 | 1984年1月 | Knurling |
| ASME B94.7*ANSI B 94.7 | 1980年1月 | Hobs |
| ASME B94.9*ANSI B 94.9 | 1999年1月 | Taps - Ground and cut threads (inch and metric sizes) |
| ASME B94.11M*ANSI B 94.11M | 1993年1月 | Twist drills |
| ASME B94.19 | 1997年1月 | Milling cutters and end mills |
| ASME B94.21*USAS B 94.21 | 1968年1月 | Gear shaper cutters |
| ASME B94.30*ANSI B 95.30 | 1970年1月 | Die buttons - Variable, press fit |
| ASME B94.33*ANSI B 94.33 | 1996年1月 | Jig bushings |
| ASME B94.33.1 | 1998年1月 | Jig Bushings, Metric |
| ASME B94.35*ANSI B 94.35 | 1972年1月 | Drill drivers - Split-sleeve, collet type |
| ASME B94.37M*ANSI B 94.37M | 1979年1月 | Roller turner type cutting tools, single point |
| ASME B94.49*ANSI B 94.49 | 1975年1月 | Spade drill blades and spade drill holders |
| ASME B94.50*ANSI B 94.50 | 1975年1月 | Basic nomenclature and definitions for single-point cutting tools |
| ASME B94.51M*ANSI B 94.51M | 1999年1月 | Specifications for band saw blades (metal cutting) |
| ASME B94.52M*ANSI B 94.52M | 1999年1月 | Specifications for hacksaw blades |
| ASME B94.53*ANSI B 94.53 | 1978年1月 | Solid steel rectangular metal cutting squaring shear knives - Dimensional tolerances |
| ASME B94.54*ANSI B 94.54 | 1999年1月 | Specifications for hole saws, hole saw arbors, and hole saw accessoires |
| ASME B94.55M*ANSI B 94.55M | 1985年1月 | Tool life testing with single-point turning tools |
| ASME B96.1 | 2000年1月 | Welded Aluminum-Alloy Storage Tanks |
| ASME B107.1 | 2002年1月 | Socket Wrenches, Hand (Inch Series) |
| ASME B107.2 | 2002年1月 | Socket Wrenches, Extensions, Adaptors, and Universal Joints, Power Drive (Impact) (Inch Series) |
| ASME B107.3*ANSI B 107.3 | 1978年1月 | Socket wrenches, power drive (non-impact) (inch series) |
| ASME B107.4 | 2005年1月 | Driving & Spindle Ends for Portable Hand, Impact, Air & Electric Tools (Percussion Tools Excluded) |
| ASME B107.5M | 2002年1月 | Socket wrenches, hand (metric series) |
| ASME B107.6 | 1994年1月 | Wrenches, box, angled, open end, combination, flare nut, and tappet (Inch series) |
| ASME B107.8 | 2003年1月 | Adjustable Wrenches |
| ASME B107.9M*ANSI B 107.9M | 1994年1月 | Wrenches, box, angled, open end, combination, flare nut and tappet (Metric series) |
| ASME B107.9M Errata | 1996年1月 | Wrenches, box, angled, open end, combination, flare nut and tappet (Metric series); Errata |
| ASME B107.10 | 2005年1月 | Handles and Attachments for Hand Socket Wrenches |
| ASME B107.11 | 2002年1月 | Pliers: Diagonal cutting and end cutting |
| ASME B107.12 | 2004年1月 | Nut Drivers |
| ASME B107.13 | 2003年1月 | Pliers: Long Nose, Long Reach |
| ASME B107.14 | 2004年1月 | Hand Torque Tools (Mechanical) |
| ASME B107.15 | 2002年1月 | Flat tip screwdrivers |
| ASME B107.16M | 1998年1月 | Shears (metal cutting, hand) |
| ASME B107.17M*ANSI B 107.17M | 1997年1月 | Gages, wrench openings, reference |
| ASME B107.18 | 2003年1月 | Pliers: Wire Twister |
| ASME B107.19 | 2004年1月 | Pliers: Retaining Ring |
| ASME B107.20 | 2004年1月 | Pliers: Lineman's, Iron Worker's, Gas, Glass, Fence, and Battery |
| ASME B107.21 | 2005年1月 | Wrench, Crowfoot |
| ASME B107.22M*ANSI B 107.22M | 1998年1月 | Electronic cutters |
| ASME B107.22M Errata | 1999年1月 | Electronic cutters; Errata |
| ASME B107.23 | 2004年1月 | Pliers: Multiple Position, Adjustable |
| ASME B107.24 | 2002年1月 | Locking pliers |
| ASME B107.25 | 2002年1月 | Pliers: Performance Test Methods |
| ASME B107.27 | 2003年1月 | Pliers: Multiple Position, Electrical Connector |
| ASME B107.28 | 2005年1月 | Electronic Torque Instruments |
| ASME B107.29 | 2005年1月 | Electronic Tester, Hand Torque Tools |
| ASME B107.30 | 2002年1月 | Cross tip screwdrivers |
| ASME B107.31M | 1997年1月 | Screwdrivers, Cross Tip Gaging |
| ASME B107.33M | 2002年1月 | Socket Wrenches, Impact(Metric Series) |
| ASME B107.34 | 2003年1月 | Socket Wrenches for Spark Plugs |
| ASME B107.35M*ANSI B 107.35M | 1997年1月 | Nut drivers (spin type, screwdriver grip) (Metric series) |
| ASME B107.36 | 2002年1月 | Pliers: Locking, Clamp, and Tubing Pinch-Off |
| ASME B107.37 | 2003年1月 | Pliers: Wire Cutters/Strippers |
| ASME B107.38M | 1998年1月 | Electronic Pliers 1998 |
| ASME B107.41 | 2004年1月 | Nail Hammers: Safety Requirements |
| ASME B107.42M | 1997年1月 | Hatchets: Safety Requirements |
| ASME B107.43 | 2002年1月 | Wood-Splitting Wedges |
| ASME B107.44 | 2002年1月 | Glaziers' chisels and wood chisels |
| ASME B107.45 | 2002年1月 | Ripping chisels and flooring/electricians' chisels |
| ASME B107.46 | 2004年1月 | Stud, Screw and Pipe Extractors: Safety Requirements |
| ASME B107.48 | 2005年1月 | Metal Chisels, Punches, and Drift Pins |
| ASME B107.49 | 2004年1月 | Nail Sets |
| ASME B107.50M | 1998年1月 | Brick Chisels And Brick Sets: Safety Requirements |
| ASME B107.51*ANSI B 107.51 | 2001年1月 | Star drills - Safety requirements |
| ASME B107.52M | 1998年1月 | Nail Puller Bars: Safety Requirements |
| ASME B107.53 | 2004年1月 | Ball Peen Hammers: Safety Requirements |
| ASME B107.54 | 2001年1月 | Heavy Striking Tools: Safety Requirements |
| ASME B107.55 | 2002年1月 | Axes - Safety Requirements |
| ASME B107.56 | 1999年1月 | Body Repair Hammers And Dolly Blocks: Safety Requirements |
| ASME B107.57 | 2005年1月 | Bricklayer's Hammers and Prospecting Picks |
| ASME B107.58M | 1998年1月 | Riveting, Scaling, And Tinner'S Setting Hammers: Safety Requirements |
| ASME B107.59 | 2002年1月 | Slugging and Striking Wrenches |
| ASME B107.60 | 2004年1月 | Pry Bars |
| ASME B107.100 | 2002年1月 | Wrenches / Note: Includes the following documents: ASME B 107.6, ASME B 107.9, ASME B 107.39 and ASME B 107.40 |
| ASME B133.1M*ANSI B 133.1M | 1983年1月 | Gas turbine terminology |
| ASME B133.2*ANSI B 133.2 | 1977年1月 | Basic gas turbine |
| ASME B133.6*ANSI B 133.6 | 1978年1月 | Gas turbine ratings and performance |
| ASME B133.7M*ANSI B 133.7M | 1985年1月 | Gas turbine fuels |
| ASME B133.8*ANSI B 133.8 | 1977年1月 | Gas turbine installation sound emissions |
| ASME B133.9*ANSI B 133.9 | 1994年1月 | Measurement of exhaust emissions from stationary gas turbine engines |
| ASME BOI | 2001年1月 | Guide for ASME Stamp Holders for Section VIII Division 1 Vessels and the Pressure Equipment Directive |
| ASME BPE | 2005年1月 | Bioprocessing Equipment |
| ASME BPVC CCB BPV | 2004年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels |
| ASME BPVC CCB BPV Supplement 1 | 2004年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 1 |
| ASME BPVC CCB BPV Supplement 2 | 2005年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 2 |
| ASME BPVC CCB BPV Supplement 3 | 2005年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 3 |
| ASME BPVC CCB BPV Supplement 4 | 2005年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 4 |
| ASME BPVC CCB BPV Supplement 5 | 2005年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 5 |
| ASME BPVC CCB BPV Supplement 6 | 2005年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 6 |
| ASME BPVC CCB BPV Supplement 7 | 2006年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 7 |
| ASME BPVC CCB BPV Supplement 8 | 2006年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 8 |
| ASME BPVC CCB BPV Supplement 9 | 2006年1月 | ASME Boiler and Pressure Vessel Code - Code Cases: CCB BPV; Boilers and Pressure Vessels; Supplement 9 |
| ASME BPVC CCB NC | 2004年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components |
| ASME BPVC CCB NC Supplement 1 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 1 |
| ASME BPVC CCB NC Supplement 2 | 2005年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 2 |
| ASME BPVC CCB NC Supplement 3 | 2005年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 3 |
| ASME BPVC CCB NC Supplement 4 | 2005年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 4 |
| ASME BPVC CCB NC Supplement 5 | 2005年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 5 |
| ASME BPVC CCB NC Supplement 6 | 2005年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 6 |
| ASME BPVC CCB NC Supplement 7 | 2006年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 7 |
| ASME BPVC CCB NC Supplement 8 | 2006年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 8 |
| ASME BPVC CCB NC Supplement 9 | 2006年1月 | ASME Boiler & Pressure Vessel Code - Code Cases: CCB NC; Nuclear Components; Supplement 9 |
| ASME BPVC Section 1 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 1: Rules for Construction of Power Boilers |
| ASME BPVC Section 1 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 1: Rules for Construction of Power Boilers; 2005 Addenda July 1,2005 |
| ASME BPVC Section 1 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 1: Rules for Construction of Power Boilers; 2006 Addenda July 1,2006 |
| ASME BPVC Section 2 Part A | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part A: Ferrous Material Specifications |
| ASME BPVC Section 2 Part A Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part A: Ferrous Material Specifications; 2005 Addenda July 1,2005 |
| ASME BPVC Section 2 Part A Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials - Part A: Ferrous Material Specifications; 2006 Addenda July 1,2006 |
| ASME BPVC Section 2 Part B | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part B: Nonferrous Material Specifications |
| ASME BPVC Section 2 Part B Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part B: Nonferrous Material Specifications; 2005 Addenda July 1, 2005 |
| ASME BPVC Section 2 Part B Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part B: Nonferrous Material Specifications; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 2 Part C | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part C: Specifications for Welding Rods, Electrodes and Filler Metals |
| ASME BPVC Section 2 Part C Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part C: Specifications for Welding Rods, Electrodes and Filler Metals; 2005 Addenda July 1,2005 |
| ASME BPVC Section 2 Part C Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials - Part C: Specifications for Welding Rods, Electrodes and Filler Metals; 2006 Addenda July 1,2006 |
| ASME BPVC Section 2 Part D Customary | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part D: Properties (Customary) |
| ASME BPVC Section 2 Part D Customary Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part D: Properties (Customary); 2005 Addenda July 1,2005 |
| ASME BPVC Section 2 Part D Customary Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials - Part D: Properties (Customary); 2006 Addenda July 1,2006 |
| ASME BPVC Section 2 Part D Metric | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part D: Properties (Metric) |
| ASME BPVC Section 2 Part D Metric Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials; Part D: Properties (Metric); 2005 Addenda July 1,2005 |
| ASME BPVC Section 2 Part D Metric Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 2: Materials - Part D: Properties (Metric); 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Appendices | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Appendices |
| ASME BPVC Section 3 Division 1 Appendices Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Appendices; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Appendices Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components - Division 1; Appendices; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection NB | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NB; Class 1 Components |
| ASME BPVC Section 3 Division 1 Subsection NB Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NB; Class 1 Components; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection NB Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components - Division 1; Subsection NB; Class 1 Components; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection NC | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NC; Class 2 Components |
| ASME BPVC Section 3 Division 1 Subsection NC Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NC; Class 2 Components; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection NC Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components - Division 1; Subsection NC; Class 2 Components; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection ND | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection ND; Class 3 Components |
| ASME BPVC Section 3 Division 1 Subsection ND Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection ND; Class 3 Components; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection ND Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection ND; Class 3 Components; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection NE | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NE; Class MC Components |
| ASME BPVC Section 3 Division 1 Subsection NE Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NE; Class MC Components; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection NE Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NE; Class MC Components; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection NF | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NF; Supports |
| ASME BPVC Section 3 Division 1 Subsection NF Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NF; Supports; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection NF Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NF; Supports; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection NG | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NG; Core Support Structures |
| ASME BPVC Section 3 Division 1 Subsection NG Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NG; Core Support Structures; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection NG Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NG; Core Support Structures; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 1 Subsection NH | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NH; Class 1 Components in Elevated Temperature Service |
| ASME BPVC Section 3 Division 1 Subsection NH Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NH; Class 1 Components in Elevated Temperature Service; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 1 Subsection NH Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 1; Subsection NH; Class 1 Components in Elevated Temperature Service; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 2 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 2; Code for Concrete Reactor Vessels and Containments |
| ASME BPVC Section 3 Division 2 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 2; Code for Concrete Reactor Vessels and Containments; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 2 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 2; Code for Concrete Reactor Vessels and Containments; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 Division 3 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 3; Containment Systems and Transport Packaging for Spent Nuclear Fuel and High Level Radioactive Waste |
| ASME BPVC Section 3 Division 3 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Division 3; Containment Systems and Transport Packaging for Spent Nuclear Fuel and High Level Radioactive Waste; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 Division 3 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components - Division 3; Containments for Transport and Storage of Spent Nuclear Fuel and High Level Radioactive Material and Waste; 2006 Addenda July 1,2006 |
| ASME BPVC Section 3 NCA | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Subsection NCA; General Requirements for Division 1 and Division 2 |
| ASME BPVC Section 3 NCA Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components; Subsection NCA; General Requirements for Division 1 and Division 2; 2005 Addenda July 1,2005 |
| ASME BPVC Section 3 NCA Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 3: Rules for Construction of Nuclear Facility Components - Subsection NCA; General Requirements for Division 1 and Division 2; 2006 Addenda July 1,2006 |
| ASME BPVC Section 4 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 4: Rules for Construction of Heating Boilers |
| ASME BPVC Section 4 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 4: Rules for Construction of Heating Boilers; 2005 Addenda July 1,2005 |
| ASME BPVC Section 4 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 4: Rules for Construction of Heating Boilers; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 5 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 5: Nondestructive Examination |
| ASME BPVC Section 5 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 5: Nondestructive Examination; 2005 Addenda July 1,2005 |
| ASME BPVC Section 5 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 5: Nondestructive Examination; 2006 Addenda July 1,2006 |
| ASME BPVC Section 6 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 6: Recommended Rules for Care and Operation of Heating Boilers |
| ASME BPVC Section 6 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 6: Recommended Rules for Care and Operation of Heating Boilers; 2005 Addenda July 1,2005 |
| ASME BPVC Section 6 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 6: Recommended Rules for Care and Operation of Heating Boilers; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 7 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 7: Recommended Guidelines for the Care of Power Boilers |
| ASME BPVC Section 7 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 7: Recommended Guidelines for the Care of Power Boilers; 2005 Addenda July 1,2005 |
| ASME BPVC Section 7 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 7: Recommended Guidelines for the Care of Power Boilers; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 8 Division 1 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 1; Pressure Vessels |
| ASME BPVC Section 8 Division 1 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 1; Pressure Vessels; 2005 Addenda July 1,2005 |
| ASME BPVC Section 8 Division 1 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 1; Pressure Vessels; 2006 Addenda July 1,2006 |
| ASME BPVC Section 8 Division 2 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 2; Alternative Rules |
| ASME BPVC Section 8 Division 2 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 2; Alternative Rules; 2005 Addenda July 1,2005 |
| ASME BPVC Section 8 Division 2 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels - Division 2; Alternative Rules; 2006 Addenda July 1,2006 |
| ASME BPVC Section 8 Division 3 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 3; Alternative Rules for Construction of High Pressure Vessels |
| ASME BPVC Section 8 Division 3 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 3; Alternative Rules for Construction of High Pressure Vessels; 2005 Addenda July 1,2005 |
| ASME BPVC Section 8 Division 3 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 8: Rules for Construction of Pressure Vessels; Division 3; Alternative Rules for Construction of High Pressure Vessels; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 9 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 9: Welding and Brazing Qualifications |
| ASME BPVC Section 9 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 9: Welding and Brazing Qualifications; 2005 Addenda July 1,2005 |
| ASME BPVC Section 9 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 9: Qualification Standard for Welding and Brazing Procedures, Welders, Brazers, and Welding and Brazing Operators; 2006 Addenda July 1,2006 |
| ASME BPVC Section 10 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 10: Fiber-Reinforced Plastic Pressure Vessels |
| ASME BPVC Section 10 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 10: Fiber-Reinforced Plastic Pressure Vessels; 2005 Addenda July 1,2005 |
| ASME BPVC Section 10 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 10: Fiber-Reinforced Plastic Pressure Vessels; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 11 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 11: Rules for Inservice Inspection of Nuclear Power Plant Components |
| ASME BPVC Section 11 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 11: Rules for Inservice Inspection of Nuclear Power Plant Components; 2005 Addenda July 1,2005 |
| ASME BPVC Section 11 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 11: Rules for Inservice Inspection of Nuclear Power Plant Components; 2006 Addenda July 1, 2006 |
| ASME BPVC Section 12 | 2004年1月 | ASME Boiler & Pressure Vessel Code - Section 12: Rules for Construction and Continued Service of Transport Tanks |
| ASME BPVC Section 12 Addenda | 2005-07-00 | ASME Boiler & Pressure Vessel Code - Section 12: Rules for Construction and Continued Service of Transport Tanks; 2005 Addenda July 1,2005 |
| ASME BPVC Section 12 Addenda 2006 | 2006-07-00 | ASME Boiler & Pressure Vessel Code - Section 12: Rules for Construction and Continued Service of Transport Tanks; 2006 Addenda July 1, 2006 |
| ASME BTH-1 | 2005年1月 | Design of Below-the-Hook Lifting Devices |
| ASME CSD-1 | 2004年1月 | Controls and Safety Devices for Automatically Fired Boilers |
| ASME H-3 | 1995年1月 | Manufacturer's Data Report For Watertube Boilers |
| ASME H-4 | 1995年1月 | Manufacturer's Partial Data Report |
| ASME H-5 | 1991年1月 | Manufacturer's Master Data Report For Boilers Constructed From Cast Iron |
| ASME HC-1 | 2002年1月 | Manufacturer's Material Certificate of Conformance for Cast Iron Boiler Sections Data Report Form (7/01) |
| ASME HC-2 | 2002年1月 | Manufacturer's Material Certificate of Conformance for Hydrostatic Testing of Cast Iron Boiler Sections ta Rp |
| ASME HLW-6 | 1991年1月 | Manufacturer's Data Report For Water Heaters Of Storage Tanks |
| ASME HLW-8 | 1991年1月 | Manufacturer's Master Data Proof Test Report For Water Heaters Or Storage Tanks |
| ASME HPS | 2003年1月 | High pressure systems |
| ASME HST-1 | 1999年1月 | Performance Standard for Electric Chain Hoists |
| ASME HST-2 | 1999年1月 | Performance standard for hand chain manually operated chain hoists |
| ASME HST-3 | 1999年1月 | Performance Standard for Manually Lever Operated Chain Hoists |
| ASME HST-4 | 1999年1月 | Performance standard for overhead electric wire rope hoists |
| ASME HST-5 | 1999年1月 | Performance standard for air chain hoists |
| ASME HST-6 | 1999年1月 | Performance standard for air wire rope hoists |
| ASME K-1 | 1997年1月 | Manufacturer's Data Report For High Pressure Vessels |
| ASME K-2 | 1997年1月 | Manufacturer's Partial Data Report For High Pressure Vessels |
| ASME K-3 | 1997年1月 | Manufacturer's Data Report Supplementary Sheet |
| ASME MC 88.2*ANSI MC 88.2 | 1974年1月 | Procedure for bench calibration of tank level gaging tapes and sounding rules |
| ASME MFC-1M | 2003年1月 | Glossary of Terms Used in the Measurement of Fluid Flow in Pipes |
| ASME MFC-2M*ANSI MFC-2M | 1983年1月 | Measurement uncertainty for fluid flow in closed conduits |
| ASME MFC-3M | 2004年1月 | Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi |
| ASME MFC-4M*ANSI MFC-4M | 1986年1月 | Measurement of gas flow by turbine meters |
| ASME MFC-5M*ANSI MFC-5M | 1985年1月 | Measurement of liquid flow in closed conduits using transit-time ultrasonic flowmeters |
| ASME MFC-6M | 1998年1月 | Measurement Of Fluid Flow In Pipes Using Vortex Flowmeters |
| ASME MFC-7M*ANSI MFC-7M | 1987年1月 | Measurement of gas flow by means of critical flow Venturi nozzles |
| ASME MFC-8M | 2001年1月 | Fluid Flow in Closed Conduits: Connections for Pressure Signal Transmissions Between Primary & Secondary Devices |
| ASME MFC-9M*ANSI MFC-9M | 1988年1月 | Measurement of liquid flow in closed conduits by weighing method |
| ASME MFC-9M Errata*ANSI MFC-9M Errata | 1989年1月 | Measurement of liquid flow in closed conduits by weighing method; Errata |
| ASME MFC-10M | 2000年1月 | Method for Establishing Installation Effects on Flow Meters |
| ASME MFC-11M | 2003年1月 | Measurement of fluid flow by means of Coriolis mass flowmeters |
| ASME MFC-12M | 2006年1月 | Measurement of Fluid Flow in Closed Conduits Using Multiport Averaging Pitot Primary Elements |
| ASME MFC-14M | 2003年1月 | Measurement of fluid flow using small bore precision orifice meters |
| ASME MFC-16M*ANSI MFC-16M | 1995年1月 | Measurement of fluid flow in closed conduits by means of electromagnetic flowmeters |
| ASME MFC-18M | 2001年1月 | Measurement of Fluid Flow Using Variable Area Meters |
| ASME MH1 | 2005年1月 | Pallets, Slip Sheets, and Other Bases for Unit Loads |
| ASME MH1.1.2*ANSI MH 1.1.2 | 1996年1月 | Definitions and terminology covering pallets and related structures |
| ASME MH1.2.2M*ANSI MH 1.2.2M | 1989年1月 | Pallet sizes / Note: Approved as MH 1.2.2 on August 1998 |
| ASME MH1.5M*ANSI MH 1.5M | 1993年1月 | Slip sheets / Note: Approved on August 1998 |
| ASME MH1.6*ANSI MH 1.6 | 1987年1月 | Standard procedures for determination of durability of wooden pallets and related structures / Note: Approved on July 1996 |
| ASME MH1.7M*ANSI MH 1.7M | 1988年1月 | Driven fasteners for assembly of pallets and related structures / Note: Approved on July 1996 |
| ASME MH1.8M*ANSI MH 1.8M | 1996年1月 | Wood pallets / Note: Approved as MH 1.8 on August 1998 |
| ASME MH1.9 | 1993年1月 | Export pallets / Note: Approved on January 1998 |
| ASME N-1 | 1988年1月 | Certificate Holders' Data Report For Nuclear Vessels |
| ASME N-1A | 1988年1月 | Certificate Holders' Data Report Nuclear Vessels (Alternate Form Single Chamber Comp Shop-Fabricated Vessels) |
| ASME N-2 | 1988年1月 | Certificate Holders' Data Report For Identical Nuclear Parts & Appurtenances |
| ASME N-3 | 1988年1月 | Owners' Data Report For Nuclear Power Plant Components |
| ASME N-5 | 1988年1月 | Cert Holders' Data Report/Inst Or Shop Assembly Nuclear Power Plant Components,Supports & Appurtenances |
| ASME N-6 | 1988年1月 | Certificate Holders' Data Report Storage Tanks |
| ASME N-7 | 2002年1月 | Nuclear Containments Data Report (07/01) |
| ASME N-8 | 2002年1月 | Class SC or Tc Closure Welds Data Report Forms (07/01) |
| ASME N-9 | 2002年1月 | Shop Fabricated Containment Parts and Appurtenances Data Report (07/01) |
| ASME N278.1*ANSI N 278.1 | 1975年1月 | Self-operated and power-operated safety-related valves - Functional specification standard |
| ASME N509 | 2002年1月 | Nuclear Power Plant Air-Cleaning Units and Components |
| ASME N510*ANSI N 510 | 1989年1月 | Testing of nuclear air treatment systems |
| ASME N510 Errata*ANSI N 510 Errata | 1991年1月 | Testing of nuclear air treatment systems; Errata |
| ASME N626.3*ANSI N 626.3 | 1993年1月 | Qualifications and duties of specialized professional engineers |
| ASME NCS-1 | 1988年1月 | Certificate Holders' Data Report For Core Support Structures |
| ASME NF-1 | 1988年1月 | Certificate Holders' Data Report For Components Supports |
| ASME NIS-1 | 1988年1月 | Owners' Report For Inservice Inspections |
| ASME NIS-2 | 1995年1月 | Owners' Report For Repairs Or Replacements |
| ASME NIS-2A | 1995年1月 | Repair/Replacement Certification Record |
| ASME NM-1 | 1988年1月 | Certificate Holders' Data Report For Tubular Products & Fittings Welded With Filler Metal |
| ASME NOG-1 | 2004年1月 | Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder) |
| ASME NPP-1 | 1988年1月 | Certificate Holders' Data Report For Fabricated Nuclear Piping Sub-Assemblies |
| ASME NPV-1 | 1988年1月 | Certificate Holders' Data Report For Nuclear Pumps Or Valves |
| ASME NQA/TR | 1993年1月 | Comparison of ASME NQA-1 and ISO 9001 |
| ASME NQA-1 | 2004年1月 | Quality Assurance Requirements for Nuclear Facility Applications |
| ASME NQA-3 | 1989年1月 | Quality assurance program requirements for the collection of scientific and technical information for site characterization of high-level nuclear waste repositories |
| ASME NS-1 | 2000年1月 | Certificates Holders' Certificate of Conformance for Welded Supports |
| ASME NUM-1 | 2004年1月 | Rules for Construction of Cranes, Monorails, and Hoists (with Bridge or Trolley or Hoist of the Underhung Type) |
| ASME NV-1 | 1988年1月 | Certificate Holders' Data Report For Pressure Or Vacuum Relief Valves |
| ASME OAR-1 | 1995年1月 | Owners Activity Report |
| ASME OM | 2004年1月 | Code for Operation and Maintenance of Nuclear Power Plants |
| ASME OM-S/G | 2003年1月 | Standards and Guides for Operation and Maintenance of Nuclear Power Plants |
| ASME P-2 | 1993年1月 | Manufacturers' Data Report For All Types Of Boilers Except Watertube & Electric |
| ASME P-2A | 1993年1月 | Manufacturers' Data Report for All Types of Electric Boilers |
| ASME P-3 | 1993年1月 | Manufacturers' Data Report For Watertube Boilers, Superheaters, Waterwalls, & Economizers |
| ASME P-3A | 1993年1月 | Engineering-Contractor Data Report For A Complete Boiler Unit |
| ASME P-4 | 1996年1月 | Manufacturers' Partial Data Report |
| ASME P-4A | 1991年1月 | Manufacturers' Data Report For Fabricated Piping |
| ASME P-4B | 1999年1月 | Manufacturer's Data Report For Field Installed Mechanically Assembled Piping |
| ASME P-5 | 1991年1月 | Summary Data Report For Process Steam Generators |
| ASME P-7 | 1996年1月 | Manufacturers' Data Report For Safety Valves |
| ASME PALD | 2005年1月 | Safety Standard for Portable Automotive Lifting Devices |
| ASME PCC-1*ANSI PCC-1 | 2000年1月 | Guidelines for pressure boundary bolted flange joint assembly |
| ASME PTC PM | 1993年1月 | Performance monitoring guidelines for steam power plants |
| ASME PTC 1 | 2004年1月 | General Instructions |
| ASME PTC 2 | 2001年1月 | Definitions and values (Performance Test Codes) |
| ASME PTC 4 | 1998年1月 | Fired steam generators |
| ASME PTC 4.2*ANSI PTC 4.2 | 1969年1月 | Coal pulverizers - Supplement to performance test code for steam generating units, PTC 4.1 |
| ASME PTC 4.3*ANSI PTC 4.3 | 1968年1月 | Air heaters - Supplement to performance test code for steam generating units, PTC 4.1 |
| ASME PTC 4.4*ANSI PTC 4.4 | 1981年1月 | Gas turbine heat recovery steam generators |
| ASME PTC 5 | 1949年1月 | Reciprocating steam engines |
| ASME PTC 6 | 2004年1月 | Steam Turbines |
| ASME PTC 6 Interpretations*ANSI PTC 6 Interpretations | 1984年1月 | Interpretations 1977-1983: Steam turbines / Note: Withdrawn by mistake |
| ASME PTC 6 Report*ANSI PTC 6 Report | 1985年1月 | Guidance for evaluation of measurement uncertainty in performance tests of steam turbines |
| ASME PTC 6.2 | 2004年1月 | Steam Turbines in Combined Cycles |
| ASME PTC 6S Report*ANSI PTC 6S Report | 1988年1月 | Procedures for routine performance tests of steam turbines |
| ASME PTC 7.1 | 1962年1月 | Displacement pumps |
| ASME PTC 8.2*ANSI PTC 8.2 | 1990年1月 | Centrifugal pumps |
| ASME PTC 10 | 1997年1月 | Performance test code on compressors and exhausters |
| ASME PTC 11*ANSI PTC 11 | 1984年1月 | Fans |
| ASME PTC 12.1*ANSI PTC 12.1 | 2000年1月 | Closed feedwater heaters |
| ASME PTC 12.2 | 1998年1月 | Steam Surface Condensers |
| ASME PTC 12.3 | 1997年1月 | Deaerators |
| ASME PTC 12.4*ANSI PTC 12.4 | 1992年1月 | Moisture separator reheaters |
| ASME PTC 12.5 | 2000年1月 | Single phase heat exchangers |
| ASME PTC 17*ANSI PTC 17 | 1973年1月 | Reciprocating internal-combustion engines |
| ASME PTC 18 | 2002年1月 | Hydraulic Turbines and Pump-Turbines |
| ASME PTC 19.1 | 2005年1月 | Test Uncertainty |
| ASME PTC 19.2*ANSI PTC 19.2 | 1987年1月 | Instruments and apparatus - Part 2: Pressure measurement |
| ASME PTC 19.3*ANSI PTC 19.3 | 1974年1月 | Instruments and apparatus - Part 3: Temperature measurement |
| ASME PTC 19.5 | 2004年1月 | Flow Measurement |
| ASME PTC 19.5.1 | 1964年1月 | Instruments and apparatus - Part 5: Measurement of quantity of materials - Chapter 1: Weighing Scales |
| ASME PTC 19.7*ANSI PTC 19.7 | 1980年1月 | Instruments and apparatus - Part 7: Measurement of shaft power |
| ASME PTC 19.8*ANSI PTC 19.8 | 1970年1月 | Instruments and apparatus - Part 8: Measurement of indicated power |
| ASME PTC 19.10*ANSI PTC 19.10 | 1981年1月 | Instruments and apparatus - Part 10: Flue and exhaust gas analyses |
| ASME PTC 19.11 | 1997年1月 | Steam and water sampling, conditioning, and analysis in the power cycle |
| ASME PTC 19.14 | 1958年1月 | Instruments and apparatus - Part 14: Linear measurements |
| ASME PTC 19.22*ANSI PTC 19.22 | 1986年1月 | Instruments and apparatus - Part 22: Digital systems techniques |
| ASME PTC 19.23*ANSI PTC 19.23 | 1980年1月 | Instruments and apparatus - Part 23: Guidance manual for model testing |
| ASME PTC 20.1*ANSI PTC 20.1 | 1977年1月 | Speed and load governing systems for steam turbine-generator units |
| ASME PTC 20.2 | 1965年1月 | Overspeed trip systems for steam turbine-generator units |
| ASME PTC 20.3*ANSI PTC 20.3 | 1970年1月 | Pressure control systems used on steam turbine-generator units |
| ASME PTC 21 | 1991年1月 | Particulate matter collection equipment |
| ASME PTC 22 | 2005年1月 | Performance Test Code on Gas Turbines |
| ASME PTC 23 | 2003年1月 | Atmospheric Water Cooling Equipment |
| ASME PTC 24*ANSI PTC 24 | 1976年1月 | Ejectors |
| ASME PTC 25 | 2001年1月 | Pressure relief devices |
| ASME PTC 26 | 1962年1月 | Speed-governing systems for internal combustion engine-generator units |
| ASME PTC 29 | 2005年1月 | Speed Governing Systems for Hydraulic Turbine Generator Units |
| ASME PTC 30 | 1991年1月 | Air cooled heat exchangers |
| ASME PTC 31*ANSI PTC 31 | 1973年1月 | Ion exchange equipment |
| ASME PTC 32.1*ANSI PTC 32.1 | 1969年1月 | Nuclear steam supply systems |
| ASME PTC 32.2 Report*ANSI PTC 32.2 Report | 1978年1月 | Methods of measuring the performance of nuclear reactor fuel in light water reactors |
| ASME PTC 36 | 2004年1月 | Measurement of Industrial Sound |
| ASME PTC 38*ANSI PTC 38 | 1980年1月 | Determining the concentration of particulate matter in a gas stream |
| ASME PTC 39 | 2005年1月 | Steam Traps |
| ASME PTC 40 | 1991年1月 | Flue gas desulfurization units |
| ASME PTC 42*ANSI PTC 42 | 1988年1月 | Wind turbines |
| ASME PTC 46 | 1996年1月 | Overall Plant Performance |
| ASME PTC 50 | 2002年1月 | Fuel cell power systems performance |
| ASME PVHO-1 | 2002年1月 | Safety Standard for Pressure Vessels for Human Occupancy |
| ASME PVHO-2 | 2003年1月 | Safety Standard for Pressure Vessels for Human Occupancy: In-Service PVHO Acrylic Windows Guidelines |
| ASME QAI-1 | 2005年1月 | Qualifications for Authorized Inspection |
| ASME QB-482 | 1994年1月 | Brazing Procedure Specification (BPS) |
| ASME QB-483 | 1994年1月 | Procedure Qualification Record (PQR) |
| ASME QB-484 | 1994年1月 | Manufacturers' Record Of Brazer Or Brazing Qualification Tests |
| ASME QEI-1 | 2004年1月 | Standard for the Qualification of Elevator Inspectors |
| ASME QFO-1 | 1998年1月 | Standard for the Qualification and Certification of High Capacity Fossil Fuel Fired Plants |
| ASME QHO-1 | 2004年1月 | Standard for the Qualification and Certification of Hazardous Waste Incinerator Operators |
| ASME QME-1 | 2002年1月 | Qualification of Active Mechanical Equipment Used in Nuclear Power Plants |
| ASME QMO-1 | 2000年1月 | Standard for the Qualification and Certification of Medical Waste Incinerator Operators |
| ASME QRO-1 | 2005年1月 | Standard for the Qualification and Certification of Resource Recovery Facility Operators |
| ASME QW-482 | 1991年1月 | Suggested Format For Welding Procedure Specification (WPS) |
| ASME QW-483 | 1994年1月 | Suggested Format For Procedure Qualification Record (PQR) |
| ASME QW-484A | 2002年1月 | Suggested Format A" for Welding Operations Qualifications (WPQ) (7/02)" |
| ASME QW-484B | 2002年1月 | Suggested Format B" for Welder Performance Qualifications (WPQ) (7/01)" |
| ASME QW-485 | 2000年1月 | Suggested Format For Demonstration Of Standard Welding Procedure Specification |
| ASME RA-S | 2002年1月 | Probalistic risk assessment for nuclear power plant applications |
| ASME RA-Sa Addenda | 2003年1月 | Probalistic risk assessment for nuclear power plant applications |
| ASME RP-1 | 1988年1月 | Fabricators' Data Report For Fiber-Reinforced Plastic Pressure Vessels (Class 1) |
| ASME RP-2 | 1988年1月 | Fabricators' Partial Data Report (Class 1 Part Of Fiber Reinforced Plasic Pv Fabricated One Mfg For Ot) |
| ASME RP-3 | 1988年1月 | Fabricators' Data Report For Class II Vessels |
| ASME RP-4 | 1988年1月 | Fabricators' Partial Data Report Class II Vessels Part Fiber-Reinforced Plastic Pv Fabricated One 4 Ot |
| ASME RTP-1 | 2005年1月 | Reinforced Thermoset Plastic Corrosion Resistant Equipment |
| ASME SI-1 | 1982年1月 | ASME Orientation and Guide for use of SI-1 (Metric) Units-Ninth Edition |
| ASME SI-2 | 1976年1月 | SI units in strength of materials |
| ASME SI-3 | 1976年1月 | SI units in dynamics |
| ASME SI-4 | 1976年1月 | SI units in thermodynamics |
| ASME SI-5 | 1976年1月 | SI units in fluid mechanics |
| ASME SI-6 | 1976年1月 | SI units in kinematics |
| ASME SI-7 | 1977年1月 | SI units in heat transfer |
| ASME SI-8 | 1976年1月 | SI units in vibration |
| ASME SI-9 | 1981年1月 | Guide for metrication of codes and standards SI (metric) units |
| ASME SI-9 Errata | 1982年1月 | Guide for metrication of codes and standards SI (metric) units |
| ASME SPPE-1 | 1994年1月 | Quality assurance and certification of safety and pollution prevention equipment used in offshore oil and gas operations |
| ASME SPPE-1b Addenda*ANSI SPPE-1b Addenda | 1995年1月 | Quality assurance and certification of safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME SPPE-1c Addenda | 1995年1月 | Quality assurance and certification of safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME SPPE-1d Addenda | 1996年1月 | Quality assurance and certification of safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME SPPE-2 | 1994年1月 | Accreditation of testing laboratories for safety and pollution prevention equipment used in offshore oil and gas operations |
| ASME SPPE-2a Addenda | 1994年1月 | Accreditation of testing laboratories for safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME SPPE-2b Addenda*ANSI SPPE-2b Addenda | 1995年1月 | Accreditation of testing laboratories for safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME SPPE-2c Addenda | 1995年1月 | Accreditation of testing laboratories for safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME SPPE-2d Addenda*ANSI SPPE-2d Addenda | 1996年1月 | Accreditation of testing laboratories for safety and pollution prevention equipment used in offshore oil and gas operations; Addenda |
| ASME STP/NU-001 | 2005年1月 | Risk Initiatives in ASME Nuclear Codes and Standards |
| ASME STS-1 | 2006年1月 | Steel Stacks |
| ASME TDP-1 | 1998年1月 | Recommended Practices for the Prevention of Water Damage to Steam Tables used for Elec Power Gen |
| ASME U-1 | 1991年1月 | Manufacturers' Data Report For Pressure Vessels |
| ASME U-1A | 1987年1月 | Manufacturers' Data Report Pressure Vessels(Alter Form Single Chamber, Comp Shop-Fabricated Vessels Only) |
| ASME U-2 | 1991年1月 | Manufacturers' Partial Data Report (A Part Of A Pressure Vessel Fabricated By One Manufacturer) |
| ASME U-3 | 1992年1月 | Manufacturers' Certificate Compliance Covering Pressure Vessels To Be Stamped With The Um Symbol.See U-1J |
| ASME U-4 | 1991年1月 | Manufacturers' Data Report Supplementary Sheet |
| ASME Y10.1*ANSI Y 10.1 | 1972年1月 | Glossary of terms concerning letter symbols |
| ASME Y10.5*ANSI Y 10.5*USAS Y 10.5 | 1968年1月 | Letter symbols for quantities used in electrical science and electrical engineering |
| ASME Y10.17*ANSI Y 10.17 | 1961年1月 | Guide for selecting Greek letters used as letter symbols for engineering mathematics |
| ASME Y14.1 | 2005年1月 | Decimal Inch Drawing Sheet Size and Format |
| ASME Y14.1M | 2005年1月 | Metric Drawing Sheet Size and Format |
| ASME Y14.2M*ANSI Y 14.2M | 1992年1月 | Line conventions and lettering |
| ASME Y14.3 | 2003年1月 | Multiview and Sectional View Drawings |
| ASME Y14.4M*ANSI Y 14.4M | 1989年1月 | Pictorial drawing |
| ASME Y14.5.1M | 1994年1月 | Mathematical definition of dimensioning and tolerancing principles |
| ASME Y14.5.2 | 2000年1月 | Certification of Geometric Dimensioning and Tolerancing Professionals |
| ASME Y14.5M*ANSI Y 14.5M | 1994年1月 | Dimensioning and tolerancing |
| ASME Y14.6 | 2001年1月 | Screw thread representation |
| ASME Y14.7.1*ANSI Y 14.7.1 | 1971年1月 | Gear drawing standards - Part 1: For Spur, helical, double helical and rack |
| ASME Y14.7.2*ANSI Y 14.7.2 | 1978年1月 | Gear and spline drawing standards - Part 2: Bevel and hypoid gears |
| ASME Y14.8M*ANSI Y 14.8M | 1996年1月 | Castings and forgings |
| ASME Y14.13M*ANSI Y 14.13M | 1981年1月 | Mechanical spring representation |
| ASME Y14.24*ANSI Y 14.24 | 1999年1月 | Types and applications of engineering drawings |
| ASME Y14.26M*ANSI Y 14.26M | 1989年1月 | Digital representation for communication of product definition data |
| ASME Y14.32.1M | 1994年1月 | Chassis frames - Passenger car and light truck - Ground vehicle practices |
| ASME Y14.34M*ANSI Y 14.34M | 1996年1月 | Associated lists |
| ASME Y14.35M | 1997年1月 | Revision of engineering drawings and associated documents / Note: Reconfirmed in 2003 |
| ASME Y14.36M*ANSI Y 14.36M | 1996年1月 | Surface texture symbols |
| ASME Y14.38 | 1999年1月 | Abbreviations and acronyms |
| ASME Y14.38a Addenda | 2002年1月 | Abbreviations and acronyms; Addenda |
| ASME Y14.40.0 | 2002年1月 | Basic Rules for the Design of Graphical Symbols for Use in the Technical Documentation of Products |
| ASME Y14.40.1 | 2002年1月 | Graphic Sumbols for Diagrams, Part 1: General Information and Indexes |
| ASME Y14.40.2 | 2002年1月 | Graphical Symbols for Diagrams, Part 2: Symbols Having General Application |
| ASME Y14.40.3 | 2002年1月 | Graphical symbols for diagrams - Part 3: Connections and related devices |
| ASME Y14.40.4 | 2002年1月 | Graphical Symbols for Diagrams, Part 4: Actuators and Related Devices |
| ASME Y14.40.5 | 2002年1月 | Graphical symbols for diagrams - Part 5: Measurement and control devices |
| ASME Y14.40.7 | 2002年1月 | Graphical symbols for diagrams - Part 7: Basic mechanical components |
| ASME Y14.40.8 | 2002年1月 | Graphical Symbols for Diagrams, Part 8: Valves and Dampers |
| ASME Y14.40.9 | 2002年1月 | Graphical symbols for diagrams - Part 9: Pumps, compressors and fans |
| ASME Y14.40.11 | 2002年1月 | Graphical Symbols for Diagrams, Part 11: Devices for Heat Transfer and Heat Engines |
| ASME Y14.40.12 | 2002年1月 | Graphical Symbols for Diagrams, Part 12: Devices for Separating, Purification and Mixing |
| ASME Y14.40.15 | 2003年1月 | Graphical Symbols for Diagrams, Part 15: Installation Diagrams and Network Maps |
| ASME Y14.41 | 2003年1月 | Digital Product Definition Data Practices |
| ASME Y14.42 | 2002年1月 | Digital Approval Systems |
| ASME Y14.43 | 2003年1月 | Dimensioning and Tolerancing Principles for Gages and Fixtures |
| ASME Y14.100 | 2004年1月 | Engineering Drawing Practices |
| ASME Y32.2*ANSI Y 32.2 | 1975年1月 | Graphic symbols for electrical and electronic diagrams (Including reference designation class designation letter) (Includes IEEE 315A-1986 Supplement) |
| ASME Y32.2.3*ANSI Y 32.2.3*ASA Z 32.2.3 | 1949年1月 | Graphical symbols for pipe fittings, valves and piping |
| ASME Y32.2.4*ANSI Y 32.2.4*ASA Z 32.2.4 | 1949年1月 | Graphical symbols for heating, ventilating, and air conditioning |
| ASME Y32.2.6*ANSI Y 32.2.6*ASA Z 32.2.6 | 1950年1月 | Graphical symbols for heat-power apparatus |
| ASME Y32.4*ANSI Y 32.4 | 1977年1月 | Graphic symbols for plumbing fixtures for diagrams used in architecture and building construction |
| ASME Y32.7*ANSI Y 32.7 | 1972年1月 | Graphic symbols for railroad maps and profiles |
| ASME Y32.10*ANSI Y 32.10*USAS Y 32.10 | 1967年1月 | Graphic symbols for fluid power diagrams |
| ASME Y32.11*ASA Y 32.11 | 1961年1月 | Graphical symbols for process flow diagrams in the petroleum and chemical industries |
| ASME Y32.18*ANSI Y 32.18 | 1972年1月 | Symbols for mechanical and acoustical elements as used in schematic diagrams |
发表于 2007-8-11 13:52:26
- s! j8 |. A; [0 S# ~