Siemens NX 2406 Build 1700 (NX 2406 Series) Win64

xiongbing

Siemens NX 2406 Build 1700 (NX 2406 Series) Win64
( d7 D6 A4 }8 j

mtyh0609

刚在鹅网找到种子你就发了:L

495581361

谢谢楼主分享

vipcax

mtyh0609 发表于 2024-6-16 08:05
刚在鹅网找到种子你就发了

+ Z3 @4 [5 v9 `哪个网址，SSQ搬去那边了吗

mtyh0609

vipcax 发表于 2024-6-16 11:34
1 A' ?7 h4 ^! _' l$ u% ]哪个网址，SSQ搬去那边了吗

only-soft.org/

mtyh0609

底壁洗许可证报错[吃瓜][吃瓜]！许可证还不完整

vipcax

mtyh0609 发表于 2024-6-16 12:08
only-soft.org/

谢谢，之前在http://rutracker.org/下过，后来打不开了

alian5337

谢谢分享！！！支持分享！！！

mtyh0609

vipcax 发表于 2024-6-16 13:22
谢谢，之前在http://rutracker.org/下过，后来打不开了

不是打不开！！是你没有楼梯

mtyh0609

vipcax 发表于 2024-6-16 13:22
  b; B  S0 A1 W2 Y2 g谢谢，之前在http://rutracker.org/下过，后来打不开了

你将后面的.org改为.net就可以打开了

alian5337

mtyh0609 发表于 2024-6-16 22:28
, `* O$ Y( m3 ~/ C+ t( G你将后面的.org改为.net就可以打开了

正解！！！

mtyh0609

在许可证后面加这个代码
+ e$ _, V- s, E; b
, l" Y9 b2 L( zINCREMENT nx_floor_wall ugslmd 2412.12 permanent uncounted SUPERSEDE \
2 ?4 i3 P% i' j4 ^5 L3 A. m               DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
; _! P+ z" U$ l3 Y4 N8 f; q               SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"

alian5337

INCREMENT Mill_planar ugslmd 2312.12 permanent uncounted SUPERSEDE \
8 l. M. x: }+ V9 N! bDUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
& G  ]5 v+ k- rSIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT Mill_plana ugslmd 2312.12 permanent uncounted SUPERSEDE \
DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
INCREMENT CAM_legacy ugslmd 2312.12 permanent uncounted SUPERSEDE \
DUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
3 ]9 O5 [0 E0 Z; v9 b; S& q' }SIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"
, V5 h! d4 \8 V$ Z; t5 }INCREMENT CAM_test_new ugslmd 2312.12 permanent uncounted SUPERSEDE \
1 z7 i$ A, F7 B; tDUP_GROUP=UHD ISSUED=01-jan-2016 CK=160 HOSTID=ANY TS_OK NOTICE="TeAM SolidSQUAD-SSQ" \
7 p+ I5 y# Q, j0 Z& D& X* bSIGN="1E33 7B88 808D 72F4 20A3 37A2 DF0C 5C20 62AE FB2D DC29 3A89 DCFB 0F6D 2BE9"

alian5337

Mill_planar---Floor Facing Without Wall
Mill_plana---Floor ang Wall
+ z- }8 U; D; R" e) F" pMill_plana---Pocket Milling
0 B5 k. ?* o$ q; \5 |$ FMill_plana---2D Profile Wall without Floor
. ~4 [, [8 i& s7 j' \! HMill_plana---2D Profile Wall with Floor
CAM_legacy---Legacy 3D Modeled Chamfers
CAM_test_new---Floor Finish Barrel Swarf
1 A# |% e: X5 |& B; @CAM_test_new---2D Wall Mill

chxking

能正常使用吗？

xiaopan

谢谢楼主分享