X9后处理出来了程序P后面一直带小数点，请问怎么解决，还有生成程序的小数点前面可...

bswbg16

X9生成程序P后面一直都带小数点，请问怎么取消，还有生成出的程序可以在小数点前面加上零吗，比如 .85可以改成0.85吗，请教各位大神

饭好香啊

没必要这样吧，所以也懒得想这个问退了

bswbg16

P值后面有小数点机床会报警，怎么能把小数点去掉

TS拾荒者

改后处理咯

bswbg16

不会改，大神有没有3轴法兰克的后处理发个给小弟，或者给小弟截个图看改后处理的那部分，万分感谢

MACI9135

# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
# --------------------------------------------------------------------------
#Default english/metric position format statements
5 P" _5 f" n7 L$ v0 G# Ofs2 1   0.7 0.6     #Decimal, absolute, 7 place, default for initialize ( 改  fs2 1   0.4 1.3l
; @) u- R, N- a/ `0 ufs2 2   0.4 0.3     #Decimal, absolute, 4/3 place
fs2 3   0.4 0.3d    #Decimal, delta, 4/3 place                              改   fs2 2   0.4 0.3
/ H6 H5 [0 h! E3 c6 M#Common format statements
fs2 4   1 0 1 0     #Integer, not leading
/ f5 R' \" F4 O& h. ]1 s# Nfs2 5   2 0 2 0l    #Integer, force two leading
fs2 6   3 0 3 0l    #Integer, force three leading
8 ~+ g: l+ m" ?  [3 i# Jfs2 7   4 0 4 0l    #Integer, force four leading
' |  N0 s+ I5 u* q8 C; o8 Vfs2 9   0.1 0.1     #Decimal, absolute, 1 place
fs2 10  0.2 0.2     #Decimal, absolute, 2 place
fs2 11  0.3 0.3     #Decimal, absolute, 3 place
6 f" h$ M& i$ Z/ Z3 ^fs2 12  0.4 0.4     #Decimal, absolute, 4 place
; s8 Y8 V' r2 g* g( U- a, i8 e/ pfs2 13  0.5 0.5     #Decimal, absolute, 5 place
/ C- l9 x0 o3 I! T7 `9 S* Ufs2 14  0.3 0.3d    #Decimal, delta, 3 place
( {! e' Y. a/ s4 D5 P2 f4 Zfs2 15  0.2 0.1     #Decimal, absolute, 2/1 place (feedrate)
fs2 16  1 0 1 0n    #Integer, forced output   
fs2 17  0.2 0.3     #Decimal, absolute, 2/3 place (tapping feedrate)   改  fs2  17  1.4lt       #Decimal, absolute, four trailing
0 E5 E; x0 k9 _9 a# This format statement is used for sequence number output
, Q1 s. r2 u0 K+ o# Number of places output is determined by value for "Increment Sequence Number" in CD
8 R6 f" ?9 l! X( L# Max depth to the right of the decimal point is set in the fs statement below
fs2 21  0^7 0^7      #Decimal, 7 place, omit decimal if integer value
fs2 22  0^3 0^3      #Decimal, 3 place, omit decimal if integer value

MACI9135

更正
# --------------------------------------------------------------------------
# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
# --------------------------------------------------------------------------
#Default english/metric position format statements
fs2 1   0.7 0.6     #Decimal, absolute, 7 place, default for initialize ( 改   fs2 1   0.4 1.3l
2 Q9 `# T7 f2 H+ I) Y) o8 Vfs2 2   0.4 0.3     #Decimal, absolute, 4/3 place                           改   fs2 2   0.4 1.3l
- U  D9 y3 }, F9 F1 w0 Ufs2 3   0.4 0.3d    #Decimal, delta, 4/3 place                              
#Common format statements
- G& y+ z- i/ ^8 h/ `: nfs2 4   1 0 1 0     #Integer, not leading
fs2 5   2 0 2 0l    #Integer, force two leading
fs2 6   3 0 3 0l    #Integer, force three leading
$ N8 b5 s6 \0 c9 N  n- _2 Z; |fs2 7   4 0 4 0l    #Integer, force four leading
; L& l, Q3 f% s- N, {* Z3 ~" d. u1 Bfs2 9   0.1 0.1     #Decimal, absolute, 1 place
fs2 10  0.2 0.2     #Decimal, absolute, 2 place
2 x& m, h6 I8 ]/ }) Nfs2 11  0.3 0.3     #Decimal, absolute, 3 place
8 c4 ?' D3 x4 _# }  s; h* p  wfs2 12  0.4 0.4     #Decimal, absolute, 4 place
fs2 13  0.5 0.5     #Decimal, absolute, 5 place
fs2 14  0.3 0.3d    #Decimal, delta, 3 place
fs2 15  0.2 0.1     #Decimal, absolute, 2/1 place (feedrate)
fs2 16  1 0 1 0n    #Integer, forced output   
; C/ g/ c8 B' e; Xfs2 17  0.2 0.3     #Decimal, absolute, 2/3 place (tapping feedrate)   改  fs2  17  1.4lt        #Decimal, absolute, four trailing
# This format statement is used for sequence number output
# Number of places output is determined by value for "Increment Sequence Number" in CD
/ k8 p7 _  J! ?/ ]# Max depth to the right of the decimal point is set in the fs statement below
# c0 P3 X. Y/ Q8 L7 ^! ]3 `fs2 21  0^7 0^7      #Decimal, 7 place, omit decimal if integer value
fs2 22  0^3 0^3      #Decimal, 3 place, omit decimal if integer value

4 V! u& E' Q$ H6 I, }; m