|
|
发表于 2004-2-16 22:03:00
|
显示全部楼层
来自： 中国湖北襄阳
|
# -------------------------------------------------------------------------- # Motion NC output 运动 NC 输出 # -------------------------------------------------------------------------- #绝对方式输出的变量为 xabs, yabs, zabs. #增量方式输出的变量为 xinc, yinc, zinc. # -------------------------------------------------------------------------- prapidout #输出直线运动的NC指令 - 快速 pcan1, pbld, n, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, strcantext, scoolant, e plinout #输出直线运动的NC指令 - 进给 pcan1, pbld, n, sgplane, `sgcode, sgabsinc, pccdia, pxout, pyout, pzout, feed, strcantext, scoolant, e pcirout #输出圆弧插补的NC指令 if arcrad >= max_arc, result = mprint(saxiswarn) pcan1, pbld, n, sgplane, sgcode, sgabsinc, pccdia, pxout, pyout, pzout, parc, feed, strcantext, scoolant, e pcom_moveb #Common motion preparation routines, before pxyzcout ps_inc_calc pncoutput #Movement output pcom_moveb comment pcan if gcode = zero, prapidout if gcode = one, plinout if gcode > one & gcode < four, pcirout pcom_movea pcom_movea #Common motion preparation routines, after pcan2 pe_inc_calc pdwl_spd #Call from NCI gcode 4 pspindle comment if prv_spdir2 <> spdir2, pbld, n, *sm05, e if prv_speed <> speed | prv_spdir2 <> spdir2, pbld, n, *speed, *spindle, pgear, e pcan if fmtrnd(dwell), pcan1, pbld, n, *sgcode, *dwell, strcantext, e else, pcan1, pbld, n, strcantext, e pcan2 prapid #输出直线运动的NC指令 - 快速 pncoutput pzrapid #输出直线运动的NC指令 - 快速 Z only pncoutput plin #输出直线运动的NC指令 - 进给 pncoutput pz #输出直线运动的NC指令 - 进给 Z only pncoutput pmx #输出NCI向量的NC指令 pncoutput pcir #输出圆弧插补的NC指令 pncoutput # -------------------------------------------------------------------------- # Motion output components 运动输出组成 # -------------------------------------------------------------------------- pbld #Canned text - 单节删除 if bld, '/' pfbld #强制 - 单节删除 "/" pccdia #切削补偿 #Force Dxx# if prv_cc_pos <> cc_pos & cc_pos, prv_tloffno = c9k sccomp if cc_pos, tloffno pfxout #Force X axis output if absinc = zero, *xabs, !xinc else, *xinc, !xabs pxout #X output if absinc = zero, xabs, !xinc else, xinc, !xabs pfyout #Force Y axis output if absinc = zero, *yabs, !yinc else, *yinc, !yabs pyout #Y output if absinc = zero, yabs, !yinc else, yinc, !yabs pfzout #Force Z axis output if absinc = zero, *zabs, !zinc else, *zinc, !zabs pzout #Z output if absinc = zero, zabs, !zinc else, zinc, !zabs parc #选择圆弧输出格式 if arcoutput = zero, [ #圆弧输出为 IJK i, j, k ] else, [ #圆弧输出为 R if abs(sweep)<=180 | arcoutput=one, result = nwadrs(srad, arcrad) else, result = nwadrs(srminus, arcrad) *arcrad ] # -------------------------------------------------------------------------- # Drilling 钻孔 # -------------------------------------------------------------------------- pdrlcommonb #Canned Drill Cycle common call, before if gcode = 81, [ result = newfs (two, zinc) if drillcyc = three, drlgsel = fsg1(-ss) + drillcyc * two else, drlgsel = fsg2(dwell) + drillcyc * two if initht <> refht, drillref = zero else, drillref = one prv_refht_a = c9k prv_refht_i = c9k ] z = depth prv_zia = initht feed = fr_pos prv_dwell = zero @dwell pcom_moveb comment pcan prdrlout #R drill position refht_a = refht refht_i = refht - initht if absinc = zero, refht_a, !refht_i else, refht_i, !refht_a pdrill #钻孔固定循环 pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, dwell, *feed, strcantext, e pcom_movea ppeck #啄式钻孔固定循环 pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *peck1, *feed, strcantext, e pcom_movea pchpbrk #断屑固定循环 pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *peck1, *feed, strcantext, e pcom_movea ptap #攻螺纹固定循环 pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *feed, strcantext, e pcom_movea pbore1 #镗孔固定循环 #1 pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, dwell, *feed, strcantext, e pcom_movea pbore2 #镗孔固定循环 #2 pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *feed, strcantext, e pcom_movea pmisc1 #Canned Misc #1 Cycle pdrlcommonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, shftdrl, dwell, *feed, strcantext, e pcom_movea pmisc2 #Canned Misc #2 Cycle (User Option) pdrill pdrill_2 #Canned Drill Cycle, additional points pdrlcommonb pcan1, pbld, n, pxout, pyout, pzout, prdrlout, dwell, feed, strcantext, e pcom_movea ppeck_2 #Canned Peck Drill Cycle pdrill_2 pchpbrk_2 #Canned Chip Break Cycle pdrill_2 ptap_2 #Canned Tap Cycle pdrill_2 pbore1_2 #Canned Bore #1 Cycle pdrill_2 pbore2_2 #Canned Bore #2 Cycle pdrill_2 pmisc1_2 #Canned Misc #1 Cycle pdrill_2 pmisc2_2 #Canned Misc #2 Cycle pdrill_2 pdrlcst #自定义钻孔循环 8 - 19 (user option) #Use this postblock to customize drilling cycles 8 - 19 pdrlcommonb "CUSTOMIZABLE DRILL CYCLE ", pfxout, pfyout, pfzout, e pcom_movea pdrlcst_2 #自定义钻孔循环 8 - 19, additional points (user option) #Use this postblock to customize drilling cycles 8 - 19 pdrlcommonb "CUSTOMIZABLE DRILL CYCLE ", pfxout, pfyout, pfzout, e pcom_movea pcanceldc #Cancel canned drill cycle result = newfs (three, zinc) z = initht prv_zia = initht pxyzcout !zabs, !zinc prv_gcode = zero pbld, n, "G80", e |
|
楼主
", e pstrtool #Comment for tool if strtool <> sblank, [ strtool = ucase(strtool) *strtool, " " ] pcomment #Comment from manual entry (must call pcomment2 if booleans) pcomment2 pcomment2 #Comment from manual entry scomm = ucase (scomm) if gcode = 1007, "(", scomm, ")" else, "(", scomm, ")", e # -------------------------------------------------------------------------- # 文件起始和刀具交换设置 # -------------------------------------------------------------------------- psof0 #Start of file for tool zero psof psof #Start of file for non-zero tool number toolchng = one if ntools = one, [ #skip single tool outputs, stagetool must be on stagetool = m_one !next_tool ] "%", e *progno, e "(PROGRAM NAME - ", progname, ")", e "(DATE=Day-Month-Year - ", date, " TIME=Hr:Min - ", time, ")", e ptoolcomment pbld, n, *sgcode, *sgplane, "G40", "G49", "G80", "G54", *sgabsinc, *smetric, e sav_absinc = absinc pcom_moveb absinc = zero pcan1, pbld, n, *sgcode, *sgabsinc, pwcs, pfxout, pfyout, *zr, *speed, *spindle, pgear, strcantext, e pe_inc_calc ps_inc_calc absinc = sav_absinc pbld, n, sgabsinc, e pretract #刀具路径末尾，换刀 sav_absinc = absinc absinc = one sav_coolant = coolant coolant = zero #cc_pos is reset in the toolchange here cc_pos = zero gcode = zero pbld, n, sccomp, *sm05, e absinc = sav_absinc coolant = sav_coolant peof0 #End of file for tool zero peof peof #End of file for non-zero tool pretract comment #Remove pound character to output first tool with staged tools # #if stagetool = one, pbld, n, *first_tool, e n, "M30", e "%", e pwcs #G54+ coordinate setting at toolchange if workofs <> prv_workofs | (force_wcs & toolchng), [ if workofs < 6, [ g_wcs = workofs + 54 *g_wcs ] else, [ p_wcs = workofs - five "G54.1", *p_wcs ] ] !workofs pgear #Find spindle gear from lookup table if use_gear = one, [ gear = frange (one, speed) *gear ] #换刀设置 pspindle #主轴转速计算 for RPM speed = abs(ss) if maxss = zero | maxss > max_speed, maxss = max_speed if speed > max_speed, speed = maxss if speed < min_speed, speed = min_speed spdir2 = fsg3(spdir) pq #Setup post based on switch settings if stagetool = one, bldnxtool = one if arctype = one | arctype = four, [ result = newfs(two, i) result = newfs(two, j) result = newfs(two, k) ] else, [ result = newfs(three, i) result = newfs(three, j) result = newfs(three, k) ] pheader #文件开始前调用 if met_tool = one, #米制常量和变量调整 [ ltol = ltol_m vtol = vtol_m maxfeedpm = maxfeedpm_m ] ptoolend #刀具路径末尾,读取新刀具资料之前 !speed, !spdir2 ptlchg1002 #Call at actual toolchange, end last path here pspindle if gcode = 1000, [ #Null toolchange ] else, [ #Toolchange and Start of file if gcode = 1002, [ #Actual toolchange pretract ] if stagetool = one, prv_next_tool = m_one prv_xia = vequ(xh) prv_feed = c9k ]