X9后处理出来了程序P后面一直带小数点，请问怎么解决，还有生成程序的小数点前面可...

bswbg16

; G7 H! q' n& z( P. c% ~6 A. H" u+ U  cX9生成程序P后面一直都带小数点，请问怎么取消，还有生成出的程序可以在小数点前面加上零吗，比如 .85可以改成0.85吗，请教各位大神

饭好香啊

没必要这样吧，所以也懒得想这个问退了

bswbg16

P值后面有小数点机床会报警，怎么能把小数点去掉

TS拾荒者

改后处理咯

bswbg16

不会改，大神有没有3轴法兰克的后处理发个给小弟，或者给小弟截个图看改后处理的那部分，万分感谢

MACI9135

# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
' ?1 G, C3 [7 f& b# --------------------------------------------------------------------------
#Default english/metric position format statements
fs2 1   0.7 0.6     #Decimal, absolute, 7 place, default for initialize ( 改  fs2 1   0.4 1.3l
4 K1 J) B8 b5 C4 W% Jfs2 2   0.4 0.3     #Decimal, absolute, 4/3 place
fs2 3   0.4 0.3d    #Decimal, delta, 4/3 place                              改   fs2 2   0.4 0.3
3 |7 ~* y/ L: W* A7 f, L3 Z, C#Common format statements
fs2 4   1 0 1 0     #Integer, not leading
fs2 5   2 0 2 0l    #Integer, force two leading
fs2 6   3 0 3 0l    #Integer, force three leading
fs2 7   4 0 4 0l    #Integer, force four leading
fs2 9   0.1 0.1     #Decimal, absolute, 1 place
+ I* \: B( W: [fs2 10  0.2 0.2     #Decimal, absolute, 2 place
fs2 11  0.3 0.3     #Decimal, absolute, 3 place
fs2 12  0.4 0.4     #Decimal, absolute, 4 place
fs2 13  0.5 0.5     #Decimal, absolute, 5 place
fs2 14  0.3 0.3d    #Decimal, delta, 3 place
# ^2 `: }  M+ gfs2 15  0.2 0.1     #Decimal, absolute, 2/1 place (feedrate)
fs2 16  1 0 1 0n    #Integer, forced output   
' J" x( o7 q! Q  d  C' X0 ?fs2 17  0.2 0.3     #Decimal, absolute, 2/3 place (tapping feedrate)   改  fs2  17  1.4lt       #Decimal, absolute, four trailing
" [4 E" f8 O  v5 X4 D# This format statement is used for sequence number output
2 z2 Z& |( V- y7 K+ @! i; i4 v# Number of places output is determined by value for "Increment Sequence Number" in CD
# Max depth to the right of the decimal point is set in the fs statement below
* F% e2 s/ {% `fs2 21  0^7 0^7      #Decimal, 7 place, omit decimal if integer value
fs2 22  0^3 0^3      #Decimal, 3 place, omit decimal if integer value
. E6 T2 U4 O. b: e3 z/ f9 {

MACI9135

更正
. k; R% o2 c* p# --------------------------------------------------------------------------
# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
$ k' H$ S8 A2 [& t- t# k, z# --------------------------------------------------------------------------
#Default english/metric position format statements
fs2 1   0.7 0.6     #Decimal, absolute, 7 place, default for initialize ( 改   fs2 1   0.4 1.3l
fs2 2   0.4 0.3     #Decimal, absolute, 4/3 place                           改   fs2 2   0.4 1.3l
fs2 3   0.4 0.3d    #Decimal, delta, 4/3 place                              
; e9 y! D  K: A1 U1 b#Common format statements
, Z$ x% Z8 ^1 p2 Ffs2 4   1 0 1 0     #Integer, not leading
" C) d0 t! p3 t! K0 l0 J7 Wfs2 5   2 0 2 0l    #Integer, force two leading
fs2 6   3 0 3 0l    #Integer, force three leading
( @8 C  i$ j2 e( dfs2 7   4 0 4 0l    #Integer, force four leading
- O$ L8 ~' n1 U" g+ O% n* Ifs2 9   0.1 0.1     #Decimal, absolute, 1 place
fs2 10  0.2 0.2     #Decimal, absolute, 2 place
4 c. U! d6 s, Hfs2 11  0.3 0.3     #Decimal, absolute, 3 place
fs2 12  0.4 0.4     #Decimal, absolute, 4 place
fs2 13  0.5 0.5     #Decimal, absolute, 5 place
fs2 14  0.3 0.3d    #Decimal, delta, 3 place
fs2 15  0.2 0.1     #Decimal, absolute, 2/1 place (feedrate)
fs2 16  1 0 1 0n    #Integer, forced output   
1 U/ v0 Z. h; K/ \; b, v* hfs2 17  0.2 0.3     #Decimal, absolute, 2/3 place (tapping feedrate)   改  fs2  17  1.4lt        #Decimal, absolute, four trailing
3 Q+ l4 s; Y: t* a- g+ i6 D+ `# This format statement is used for sequence number output
3 y: u+ _; c5 ^! |) I; G# Number of places output is determined by value for "Increment Sequence Number" in CD
# Max depth to the right of the decimal point is set in the fs statement below
fs2 21  0^7 0^7      #Decimal, 7 place, omit decimal if integer value
9 M) ~) q3 }. a) O' Kfs2 22  0^3 0^3      #Decimal, 3 place, omit decimal if integer value
5 k' O( w+ G; v