|
|
楼主 |
发表于 2015-11-7 22:00:18
|
显示全部楼层
来自： 中国广东广州
多谢各位现在不用备刀，西门子的备刀我也不懂，我这个程式钻孔是没有问题的，
8 ?6 e, M6 ^4 j%_N_ 01 _MPF! Z" x6 r- p. d- a V
;$PATH=/_N_WKS_DIR/_N_WD_WPD
- `5 c- _) r; { j7 S;(***05-11-15*** ***16:37***)
& y, J- u8 x5 I! ?* j2 ?" R;(T1 30 BULL-NOSED ENDMILL )
6 I: c! }, ?3 n;(T2 17 BULL-NOSED ENDMILL )
( e5 W" r m1 p: m+ Q- O1 U L8 }% R$ ];(T3 26 BULL-NOSED ENDMILL )
, \ L/ k' g+ p4 G4 v2 M, _( j;(T5 10 FLAT ENDMILL )& C/ C) l9 J% N0 }/ ^/ |9 S
;(T6 10 FLAT ENDMILL ). ^$ j1 M, r$ N3 s3 [& ]
;(T106 CHAMFER MILL )
# ]* I0 w9 n ?" g;(T7 STANDARD DRILL - 3 )
6 V1 S4 U$ ~4 o1 m5 ]9 J3 R;(T9 STANDARD DRILL - 4.3 )* C$ a5 L8 s! L, g
;(T8 STANDARD DRILL - 3.3 )1 N9 v/ Z$ G; O
;(OVERALL MAX - Z20.)
' X; P9 P2 g5 O3 G$ z# T;(OVERALL MIN - Z-22.)
) L( L: L' m0 _& ~! |G64 SOFT
- D9 _! s3 ?3 M: F; mG54* o& Z: ~- \/ S2 {. t6 X
T1
C! o: q6 [% N" t' U0 _! @: x6 M& |- SM06
7 C; H3 m" {/ Z3 U;( 30 BULL-NOSED ENDMILL )
8 t" q: ^8 ^: x+ _& VG00 G90 X68. Y-39.344 S2500 M03! W9 j, ~( O( F* \; y* |& d4 B! q
G01 Z20. F5000# D4 P s/ z, d8 y' Y! p* r
M08) w+ x5 _, q+ N; K- Z7 p
;(MAX - Z20.)
8 @3 a1 r7 g8 H U;(MIN - Z-5.1)
2 D: Z# z6 g0 `, RZ2.. w7 R! O8 P% s! Y* N9 M! W
G01 Z-.425 F3000.
1 H+ J; q, c+ U# `Y-8.656 F4000.# t8 Z) B$ r! N/ B( ?
X-68.$ h/ k9 i1 ~1 M6 W
Y-39.344
7 a. C9 U8 ~& |" uZ-.85 F3000.
- y F' G" ?8 ~ t% s8 ^ H& CY-8.656 F4000.
' i9 e0 V8 Y% g( ?. nX68.6 o* O4 [$ x1 u- |/ M
Y-39.344* L2 O$ P1 h3 o& G7 | [, ~
Z-1.275 F3000." U7 i5 Y: X* }# o a
Y-8.656 F4000.3 z( q" b _: ^' {; ?3 f
X-68.$ f: B% n, J; H- g
Y-39.344& ^) g! R' Z8 {5 h4 C
Z-1.7 F3000.
9 f7 J ~9 g2 h4 m* h& \Y-8.656 F4000.
9 m6 f$ f# c( ~$ H! z; v' eX68. |
|
发表于 2015-11-7 08:48:09
