|
|
楼主 |
发表于 2015-9-3 20:15:54
|
显示全部楼层
来自： 中国甘肃兰州
本帖最后由 ning84 于 2015-9-4 09:31 编辑
. N8 y. q- @, B3 N5 X+ j. o7 ^在压力容器制图，总图是1，2，3，部件图是1-1，1-2，1-3都是这种排列。
( j$ R9 I2 a- m& u. w" B大型装配图总图，部件图都是1-1,1-2排列。
@; C* w' b: G% r- W7 w, |-
# } E# D) j4 a7 K - Private Sub ll1()
, \. U) s8 J' a# h* {( M- }1 V7 j( M - Dim SwApp As SldWorks.SldWorks, SwModel As ModelDoc2& g" w" b( U1 l- b/ h# E3 E E
- Set SwApp = Application.SldWorks4 c7 m2 {2 N& }+ l
- Set SwModel = SwApp.ActiveDoc
) y% ~+ @! o1 j - Dim SwSelMgr As SelectionMgr, Str( I7 K# I P4 H0 ]! k
- Set SwSelMgr = SwModel.SelectionManager0 k& O4 G1 V2 C- Q- y1 f. t
- Dim SwNote As Note
$ r8 r* O. |3 z. b; q3 ] - Set SwNote = SwSelMgr.GetSelectedObject5(1)$ T$ v @: v* p: q% K1 R: M
- Debug.Print SwNote.GetName, SwNote.GetText
- T$ v% F5 h) T# H+ C# j - 'SwModel.EditBalloonProperties swBS_Underline, swBF_Tightest, swDetailingNoteTextCustom, "3-" & SwNote.GetText, swDetailingNoteTextItemNumber, "1"4 H% g: ^, w) z s$ Y8 w, m4 ~ `- F
- Str = "3-" & SwNote.GetText
& L* n% r% d$ x( L/ l: L - Str = ""- O9 O' r; x* y) f9 L
- 'SwModel.EditBalloonProperties swBS_Underline, swBF_Tightest, 0, Str, swDetailingNoteTextItemNumber, "1"
4 n& a0 ^5 n7 \% K2 T- y% E% J+ v - ' SwModel.EditBalloonProperties swBS_FlagTriangle, swBF_Tightest, swDetailingNoteTextQuantity, Str, swDetailingNoteTextItemNumber, "1"3 K% S8 \: N# @3 }: a) o
- SwModel.EditBalloonProperties swBS_Underline, swBF_Tightest, swDetailingNoteTextItemNumber, Str, swDetailingNoteTextItemNumber, "1"
6 F5 t7 x( u4 Y, n6 h/ j4 Y- U - 'SwModel.EditBalloonProperties 10, 0, 0, "3-2", 2, "1"% x; h/ w" o) l, c/ H
- End Sub
3 \6 f( ~" g3 [, S' H
数字+字母-零件序号问题?-SolidWorks-三维网 - Powered by Discuz!
M# s/ G8 S. u7 A( khttp://www.3dportal.cn/discuz/fo ... 3%BC%FE%D0%F2%BA%C5
! R8 V# |/ J6 u% ^7 Lhttp://www.3dportal.cn/discuz/data/attachment/forum/month_1204/12041910187644a513b37b7bb4.jpg) b# g1 n9 W% c, A# \6 ^
1 ^- E. Y9 S/ V0 m- Y% X# q! R1 @$ U
# n2 l( d$ [! Y, l! n
8 n8 z) }6 i, J4 R9 j: K; ~1 o1 j
|
|
发表于 2015-9-3 17:19:57
