|
|
楼主 |
发表于 2012-4-10 20:20:54
|
显示全部楼层
来自： 中国天津
本帖最后由 86843173 于 2012-4-10 20:24 编辑
9 B$ R! s8 e8 p. P: k- @7 [; \; I
我说的是车床1 N3 n9 [; C! E
# Format statements - n=nonmodal, l=leading, t=trailing, i=inc, d=delta
3 [# Y/ N. D0 A9 k! D7 p+ w" z# --------------------------------------------------------------------------, q2 P3 i& B# K" M
#Default english/metric position format statements
) ^: T6 t: [# X) I) L& B% rfs2 1 0.7 0.6 #Decimal, absolute, 7 place, default for initialize (
2 b z. l3 ^! H) W' S/ v& ]fs2 2 0.4 1.3l #Decimal, absolute, 4/3 place' w$ k0 }4 z. \$ S! y
fs2 3 0.4 1.3ld #Decimal, delta, 4/3 place. {( h& ~% Q* b/ L5 i7 |
#Common format statements' j$ H" @/ g6 B/ B) ~$ J
fs2 4 1 0 1 0 #Integer, not leading, e5 x4 R" X0 o8 V6 T) z
fs2 5 2 0 2 0l #Integer, force two leading
$ u$ Y6 U% B& O7 r1 yfs2 6 3 0 3 0l #Integer, force three leading9 u: x: Z% I' d0 v7 K+ k
fs2 7 4 0 4 0l #Integer, force four leading
' U/ Q Y. [2 }fs2 9 0.1 0.1 #Decimal, absolute, 1 place
/ A* x& e+ P0 S, c- Q2 gfs2 10 0.2 0.2 #Decimal, absolute, 2 place
* z4 \& `- _3 x3 b- o" n8 qfs2 11 0.3 0.3 #Decimal, absolute, 3 place
8 M4 k( |# Y3 h, \fs2 12 0.4 0.4 #Decimal, absolute, 4 place, L' h* r+ Z/ ]. m, G
fs2 13 0.5 0.5 #Decimal, absolute, 5 place
0 [, e& c3 K. f0 s/ Y$ ~fs2 14 0.3 0.3d #Decimal, delta, 3 place+ X! |! w0 X+ x, i/ q- v
fs2 15 0.2 1.1l #Decimal, absolute, 2/1 place (feedrate) 就是这里
6 v5 S$ W: k6 b+ p, [7 y9 y# Gfs2 16 0 4 0 4t #No decimal, absolute, 4 trailing+ D, U! ^4 v" g$ l' _
#Default english/metric feed format statements
3 ~" M4 q2 ]! U$ u5 a l9 Bfs2 17 0.2 0.1 #Decimal, absolute, 2/1 place4 }6 h! t+ A! B% [7 h4 g1 h8 n8 }
fs2 18 0.4 0.3 #Decimal, absolute, 4/3 place% \5 c% F+ @+ a$ l( L; s
fs2 19 0.5 0.4 #Decimal, absolute, 5/4 place: a8 V* R( F. b
fs2 20 1 0 1 0n #Integer, forced output
+ k0 K i3 O: F. N& N9 p: r0 o9 {, L6 J# These formats used for 'Date' & 'Time'
' V ~/ N. l$ D1 I* f: Y3 M. G- A+ hfs2 21 2.2 2.2lt #Decimal, force two leading & two trailing (time2)
) s, G+ G- ^9 h+ P! j3 wfs2 22 2 0 2 0t #Integer, force trailing (hour)
9 s) I' u9 U+ f' T' Ofs2 23 0 2 0 2lt #Integer, force leading & trailing (min)) R. O4 f/ K5 @& A, L
# This format statement is used for sequence number output7 E: ^& j9 _5 m( C I T# \1 x: J: M3 Q
# Number of places output is determined by value for "Increment Sequence Number" in CD+ H0 G. n9 I- w' c( L- S6 @* |2 p
# Max depth to the right of the decimal point is set in the fs statement below+ X. q/ ~7 R9 d! c N. ^
fs2 24 0^7 0^7 #Decimal, 7 place, omit decimal if integer value |
|
发表于 2012-4-9 21:38:45
发表于 2012-4-9 21:51:34
发表于 2012-4-9 23:07:40