|
|
马上注册，结识高手，享用更多资源，轻松玩转三维网社区。
您需要 登录 才可以下载或查看，没有帐号？注册
x
Composite Materials： Design and Applications (CRC 2003)1 ?1 h7 \3 ~8 K! ~& a _( m
page：523/ g6 f0 H* v- ]3 E, k3 p9 c. E
- W; \ i$ p" k! i
French editions published by Editions HermEs, Paris, 1997
# S$ V. e* J. A$ x% \) z% rNo claim to original U.S. Government works, U9 g5 d( v# l8 V4 F
International Standard Book Number 1-58716-084-6' L; T8 L: q9 M* C* b @
Library of Congress Card Number 2002073794
6 W9 z0 z L0 a' D R; K简介! u% \: [% o6 t# z4 ~
This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with0 ]2 G' \7 D- R$ K+ X
permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish0 z% P: Q% \& f! o& s- P
reliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials2 e" F# ^7 j/ |2 Z5 S
or for the consequences of their use.6 D6 E) u# W+ a. U* w$ h0 v' U
1 Composite Materials, Interest, and Properties/ R8 W3 L4 R8 z4 S
1.1 What Is Composite Material? ; \' ]& B$ U: U! ]6 T/ ]; Q: i+ G
1.2 Fibers and Matrix 4 J4 {( @0 N2 r5 y& P6 m% l$ M, b
1.2.1 Fibers # Y a+ w. X% Y4 b2 a5 K# y6 H
1.2.2 Matrix Materials 1 S: c J) ?( Q
1.3 What Can Be Made Using Composite Materials?
9 f% V' d/ H6 a3 z, r1.4 Typical Examples of Interest on the Use of Composite Materials ! D3 {8 a% _# [( U8 L
1.5 Examples on Replacing Conventional Solutions with Composites
6 \+ \4 N6 _$ _6 F4 u" O3 H$ L1.6 Principal Physical Properties
* o: B+ S P) w2 P2 Fabrication Processes. S5 a2 i Y8 [# u3 O* X* C
2.1 Molding Processes
' B1 a( M) b2 N7 m2.1.1 Contact Molding 6 H5 ^5 h3 ]3 }0 a2 W
2.1.2 Compression Molding
7 k5 b7 |$ P- N4 C" Q E2.1.3 Molding with Vacuum 5 }. h8 B; b. q+ P1 J0 Q' o
2.1.4 Resin Injection Molding
' F4 ?) n. a( | g; i0 z2.1.5 Molding by Injection of Premixed ' L7 p! A# C- A: ?3 G. y2 C/ Q0 K
2.1.6 Molding by Foam Injection : g% A) H! X% y% r+ l4 h1 N
2.1.7 Molding of Components of Revolution
2 b6 J, }1 A2 b* D; P8 g+ v2 |( h2.2 Other Forming Processes
' ^3 I$ u* M2 q& W2.2.1 Sheet Forming
! @2 h/ F6 t, {2.2.2 Profile Forming
5 D& i" [$ T5 O/ Y# l2.2.3 Stamp Forming
; J! d) _6 V8 u. E* D2.2.4 Preforming by Three-Dimensional Assembly U! I- u+ y6 M% y% E1 i
2.2.5 Cutting of Fabric and Trimming of Laminates
* U7 r$ D0 O0 F+ P4 f2.3 Practical Hints on Manufacturing Processes
$ E7 C4 l4 Y# ^& `0 R! u& c. `' o2.3.1 Acronyms
7 V! N- u, f# b$ s2.3.2 Cost Comparison 4 v j4 ]2 Q7 V7 C7 Q1 B
3 Ply Properties
a: V6 e6 m( l8 O$ l) @3.1 Isotropy and Anisotropy
# B9 j$ ]9 h6 i+ A3.1.1 Isotropic Materials 0 j$ W4 g1 y0 Y. C$ W
3.1.2 Anisotropic Material ) t2 c. q# @* ]: i# t+ s
3.2 Characteristics of the Reinforcement–Matrix Mixture " F5 c3 N; q0 G) M9 D; T
3.2.1 Fiber Mass Fraction
5 M' R7 S' n, m7 j; L7 h( ^3.2.2 Fiber Volume Fraction
" B* K# m* ~3 d# E9 K; h3.2.3 Mass Density of a Ply
$ ?2 Q" T& z. [" t! k3.2.4 Ply Thickness
5 i' k# a5 o) P5 s; O& u...............8 k a2 ^# N( E& C& e* b& z: o
共9个压缩卷，解压后18.3M+ F/ v: F/ z& O5 Z
2 o0 ?& z. D$ w! Q# \9 B[ 本帖最后由 fenglianxiang 于 2008-8-5 16:43 编辑 ] |
评分
-
查看全部评分
|
[复制链接]
发表于 2008-8-5 16:37:59
