|
|
发表于 2010-5-26 08:17:59
|
显示全部楼层
来自： 中国北京
楼主上传的文档中有不少错误.下面是修改后的代码
9 b. Q) R: E0 a( Q4 E3 u% x- (defun C:Bxh (/ p1 p2 p3 ang bxh radi txth) ;标序号4 O3 K0 A* u6 K# z; ~8 m0 Z9 B7 D
- (setq radi 5) ;圆圈半径. U$ T1 q( K; m/ l
- (setq txth 5) ;字高
1 n3 v( i- P8 r - (if (not bx) (setq bx 1))
2 _# M# N* S+ D5 Z1 C) Z8 l, x - (setq p1 (getpoint "\n请选择起点:" )) ;在零件上选一点' C9 X I. h7 R! G, B8 s
- (setq p2 (getpoint "\n请选择第二点或回车表示无第二点:" )) ;标注位置处一点8 D0 G" ~: z: k- _: d9 e) `
- (setq bxh (getint (strcat "\n请输入序号<" (itoa bx) ">:" ))) ;序号数2 ^- c. k1 J7 A/ @5 `$ S# N
- (if bxh (setq bx bxh))
, z% _- }& f0 s$ O- [ - (cond (p2' l6 P( [: g# @- ~2 s, Q4 g
- (command "layer" "set" "细实线图层名" "" ) ;改到画细线图层,使用前把"细实线图层名"改为使用者自己的相应图层名* ?0 p p$ X. f9 c2 n+ p: ?$ ?
- (setq ang (angle p1 p2))
d# R6 D& O' L+ s3 Z9 x - (setq p3 (polar p1 ang (-(distance p1 p2) radi))) ;画圆、线
6 a. j0 R6 ]: t/ C - (command "pline"9 A3 I7 [; c, m* B9 H
- (polar p1 ang 0.25)+ ]3 T9 p4 ^3 p; U- |
- "w" 0.5 0.5 "A" "CE"p1"A"359.9"L""W"0 0 p3"" )8 `' c0 _# M2 Q" P' F
- (command"circle"p2 radi)4 _& f1 G6 r/ p& X5 H) |" k; c
- (command "layer" "set" "文字图层名" "" ;改到写文字图层,使用前把"文字图层名"改为使用者自己的相应图层名$ ]$ `+ e3 A6 i6 U6 o
- "text" "J" "M" p2 txth 0 bx) ;写文字
- o: x1 H: V" K/ Z2 r/ H6 C - )# q8 ?5 e- n$ }$ m$ w; e @
- ((not p2) ;如果在零件中直接标注) b: ?7 N' ~* }
- (command "layer" "set" "细实线图层名" "" ) ;改到画细线图层,使用前把"细实线图层名"改为使用者自己的相应图层名
. X# Y7 h0 s# r8 Q - (Command "circle" p1 radi) ;画圆; Q+ j0 f5 i! ^8 E: f4 I2 [" c7 O
- (command "layer" "set" "文字图层名" "" ;改到写文字图层,使用前把"文字图层名"改为使用者自己的相应图层名+ b% Z+ B1 ?% ?9 G3 _9 y3 A" h
- "text" "J" "M" p1 txth 0 bx) ;写文字4 a- e7 Y9 W" S- Y2 d
- )$ Q7 u- ~7 c' f; Y) k' }
- )
$ C$ M% O- J, p" h$ s& N$ o. e. ^ i - (setq bx (+ bx 1)), m" {" }; C: t
- (princ)& ]! O3 q& H; o* ^) x
- )
) C: k* e. |6 o" E. h, |6 l
|
|
发表于 2010-5-25 17:46:12
楼主