Composite Materials： Design and Applications (CRC 2003)

fenglianxiang

Composite Materials： Design and Applications (CRC 2003)
page：523
% N" l1 @' f, r
French editions published by Editions HermEs, Paris, 1997
No claim to original U.S. Government works
2 u& S) R( c  Z* wInternational Standard Book Number 1-58716-084-6
2 _  }( G4 W: V5 z$ x8 hLibrary of Congress Card Number 2002073794
简介
This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with
permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish
+ [7 p$ F$ w" ^5 Vreliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials
or for the consequences of their use.
1  Composite Materials, Interest, and Properties
7 X/ u8 }: T7 o) B1.1  What Is Composite Material?
1.2  Fibers and Matrix
0 `/ R! T' M/ d; c. g1.2.1  Fibers
1.2.2  Matrix Materials
- B6 {8 B8 k# G/ e! L7 P0 [# N1.3  What Can Be Made Using Composite Materials?
8 @9 D2 ^& }& b2 u- T1.4  Typical Examples of Interest on the Use of Composite Materials
- l# d! W& f: U% h& ?! ^& V1.5  Examples on Replacing Conventional Solutions with Composites
1.6  Principal Physical Properties
+ f/ J' I4 Q8 J' N0 M. L9 j) q2 z8 c9 e2  Fabrication Processes
2.1  Molding Processes
2.1.1  Contact Molding
; i; s4 J1 t$ Y6 A' c- m3 O2.1.2  Compression Molding
4 \$ i/ R# S6 c* ~% y2.1.3  Molding with Vacuum
2 N1 g4 K" L# g$ l2.1.4  Resin Injection Molding
2.1.5  Molding by Injection of Premixed
0 ]" c% w# e& p$ s. T1 v  V2.1.6  Molding by Foam Injection
2.1.7  Molding of Components of Revolution
2.2  Other Forming Processes
2.2.1  Sheet Forming
2.2.2  Profile Forming
2.2.3  Stamp Forming
2.2.4  Preforming by Three-Dimensional Assembly
2.2.5  Cutting of Fabric and Trimming of Laminates
  \$ e4 m% P% b4 a, q0 ?# x2.3  Practical Hints on Manufacturing Processes
2.3.1  Acronyms
2.3.2  Cost Comparison
3  Ply Properties
3.1  Isotropy and Anisotropy
3.1.1  Isotropic Materials
3.1.2  Anisotropic Material
: c' J# P' i0 P, B8 w5 a3.2  Characteristics of the Reinforcement–Matrix Mixture
3.2.1  Fiber Mass Fraction
# Q& D* o4 |' [3.2.2  Fiber Volume Fraction
3 w. \1 }) A) ?8 t2 ^5 d2 V3.2.3  Mass Density of a Ply
3.2.4  Ply Thickness
" y( ]  U/ U( f; s8 b, |...............
! p5 j$ \) P( v- Z3 |共9个压缩卷，解压后18.3M

[ 本帖最后由 fenglianxiang 于 2008-8-5 16:43 编辑 ]