有关于过滤后的程序还是没有圆弧

tjhfanuc

不知道为什么，，
  我用的是mastercam9.1sp2版，但是编出来的程序没有圆弧，我用的是2：1的过滤，，可是程序在机床上用时，，机器走的很慢，，这是我现在用的后处理。。
spaces      : 1     #Number of spaces to add between fields
omitseq     : no    #Omit sequence numbers?
% }/ {0 w# e& [/ i! W6 `. i8 [seqmax      : 9999  #Max. sequence number
arcoutput   : 0     #0 = IJK, 1 = R no sign, 2 = R signed neg. over 180
arctype     : 2     #Arc center 1=abs, 2=St-Ctr, 3=Ctr-St, 4=unsigned inc.
breakarcs   : 2     #Break arcs, 0 = no, 1 = quadrants, 2 = 180deg. max arcs
4 r7 D+ J4 D" t* V4 V9 n) J3 sdo_full_arc : 1     #Allow full circle output? 0=no, 1=yes
3 I8 o0 q7 x/ Jhelix_arc   : 1     #Support helix arc output, 0=no, 1=all planes, 2=XY plane only
compwarn    : 1     #Warn if cutter comp applied on arc, 0=no, 1=yes
miscerror   : 0     #Error out if Misc Values button is disabled, 0=no, 1=yes
maxrad      : 999   #Maximum arc radius
7 k- _, J5 C1 B+ P. m* I  L' ghel_2100    : no    #Acramatic 2100 style helical moves, 0=no, 1=yes
, J8 c% a) ~# N0 e& Ousecanned   : yes   #Use canned drilling cycles?  Set to no for long output.
force_dpts  : no    #Force XY output on all drilling lines including cycle call?
; V: @8 K  O0 Vhaas_drill  : 0     #Haas style peck drill, 0=no, 1=yes
wcstype     : 2     #0 = G92 at start, 1 = G92 at toolchanges, 2 = G54, 3 = Off
% j( o% t) i7 ^3 gforce_wcs   : yes   #Force WCS output at every toolchange?
2 a# U4 `5 b2 b4 F: Vstagetool   : 0     #0 = Do not pre-stage tools, 1 = Stage tools
: r$ q# H; }5 i6 _! v; d6 f# b0 \2 gtool_table  : 1     #Tool table, 0=no, 1=yes, 2=Predator VCNC, 3=MetaCut View #
( ~2 Y% M5 e3 S2 i6 a  C4 ^: Z# Poutput_z    : yes   #Output Z Min and Z Max values (yes or no)
. B3 A* P1 ]$ w# }: o6 Q3 U/ h2 Ocool_zmove  : yes   #Coolant off with last move
use_pitch   : 0     #0 = Use feed for tapping, 1 = Use pitch for tapping
tap_feed    : 0     #0 = 2/1 (in/mm) decimal places, 1 = 4/3 (in/mm) decimal places
+ [# t6 a8 c/ K# C, |0 S0 k5 [maxfeedpm   : 500   #Limit for feed in inch/min
5 z. j3 A* ^% C& ?/ Smaxfeedpm_m : 10000 #Limit for feed in mm/min
use_gear    : 0     #Output gear selection code, 0=no, 1=yes
( o( }/ I3 m4 }, W: ]& g' dmax_speed   : 10000 #Maximum spindle speed
) y8 k5 A' T9 H& w: y3 ~$ [6 ]% \min_speed   : 50    #Minimum spindle speed
sextnc      .NC     #NC extension override
- J7 J3 d& @6 S+ L8 v1 E% mvmc         : 1     #0 = Horizontal Machine, 1 = Vertical Mill
. X! G' a4 L: L. A+ [rot_on_x    : 0     #Default Rotary Axis Orientation, See ques. 164.
                    #0 = Off, 1 = About X, 2 = About Y, 3 = About Z
9 n; G$ H/ C. V: T5 t& n0 vrot_ccw_pos : 1     #Axis signed dir, 0 = CW positive, 1 = CCW positive
  b1 C1 w( v9 T, h8 f5 m1 tret_on_indx : 1     #Machine home retract on rotary index moves, (0 = no, 1 = yes)
9 Y: Z- X& m- T  G: l6 B' Jindex       : 0     #Use index positioning, 0 = Full Rotary, 1 = Index only
: j9 b' H7 ]  ]: }6 r6 Mctable      : 5     #Degrees for each index step with indexing spindle
# D4 r4 F; Z! V: `8 k5 L# K; Z9 Bone_rev     : 0     #Limit rotary indexing between 0 and 360? (0 = No, 1 = Yes)
# A! K0 y+ X. x: _lock_codes  : 0     #Use rotary axis unlock/lock M-Codes? (0 = No, 1 = Yes)
1 j4 N5 G! o4 J  U1 A/ K! Ause_frinv   : 0     #Use Inverse Time Feedrates in 4 Axis, (0 = no, 1 = yes)
maxfrdeg    : 2000  #Limit for feed in deg/min
maxfrinv    : 999.99#Limit for feed inverse time
$ q% A9 ~& \8 t# B: Q5 i! ~frc_cinit   : 1     #Force C axis reset at toolchange
8 p7 s* n+ H- {8 Mctol        : 225   #Tolerance in deg. before rev flag changes
3 V8 k& I6 {1 P4 Q* c$ C3 Tixtol       : .01   #Tolerance in deg. for index error
frdegstp    : 10    #Step limit for rotary feed in deg/min

mubaibyby

光看后处理好像没有什么问题，把你的源文件发上来看看