|
|
马上注册，结识高手，享用更多资源，轻松玩转三维网社区。
您需要 登录 才可以下载或查看，没有帐号？注册
x
TOOL CHANGE: FIRST:
8 `5 i3 ]2 h8 Z SET_ON SPIN_SPEED SPIN_DIR ; , w% h7 Q9 Q* V) B6 h4 s4 N
*-----save first tool number
# F6 A' t' r6 X3 e FirstTool = CURR_TOOL ;
7 K% I) D8 D$ |4 f8 \6 L% e8 P LastTool = CURR_TOOL ; 3 N& o" v& A s% X6 s
& ^& p1 V+ c1 U' W3 a r$ H. ^
*-----tool cutter compensation register number
; h' S- b! W. g1 L3 b5 u CutterComp = CURR_TOOL + DiaComp ; " d. s1 I8 F: \
# w4 d/ f9 a6 j6 L' y*-----assuming 1st tool is in the spindle, there is no need * F4 z7 m% L5 _; X2 l# J6 c
* for tool change) % i# M6 ]/ O4 p( |
* OUTPUT $ " T" CURR_TOOL ;
, w1 `3 H9 B% h0 W! m0 l# I# }9 M' y*-----more then one tool in this run of the Post Processor + I4 i) a' z" q. k) [
IF_SET (NEXT_TOOL _NE_ CURR_TOOL) 5 \$ _( j; ~6 T
OUTPUT $ " T" NEXT_TOOL ;
" Z4 M* j }6 x6 A m) ] END_IF ; m, h: J" }. u7 j8 O1 `% t$ f
*-----standard tool change commands. (assuming 1st tool is in $ h: u8 y0 X/ S6 l D
OUTPUT $ " G90 G80 G00 G17 G40 G54" ;
* {2 f8 g* G+ G \+ O8 M- M6 E* Q( Y OUTPUT $ " Z" Zhome " S" SPIN_SPEED " " SPIN_DIR ;
( [& @: a- K( S* w5 O% s: Z" ` N OUTPUT $ "( 刀具名称---" CURR_NAME "×" CLEAR_LENG ")"; 3 l X G/ w# Z8 |. {
OUTPUT $ "( 曲面偏移=" PART_OFST "曲面公差=" PART_TOL" 轮廓偏移=" CONT_OFST " )";# m/ B4 @; r% U6 v/ H3 k# V8 w4 l5 Z" ^
OUTPUT $ "( 程式名称=" TP_NAME "本程式由" USER_NAME "编制 )";
R+ n- P$ W& H3 l) d# D9 t/ b+ q- _- `4 g2 c, _+ l! n3 ?- M+ R
5 ~5 N1 X3 m/ {8 t$ a
说明：1、*注释或代表不执行此内容；/ o% U1 O2 j' O1 N, {6 Q) y
2、 引号里内容则按实输出；) P: [2 {! O: W: s$ N2 N! t
3、修改保存完毕执行主菜单--NC--DFEXF--输入后处理名--回车即可。 |
|
发表于 2007-12-14 17:18:02