老大帮我呀。。。

dazhi518

模型输入以后，白色的系统坐标在电极的分中台上。建立用户坐标，用坐标器摆正，系统坐标就和用户坐标在一块了，可是我想让系统坐标在原位置上不动，只动用户坐标该如何编代码呀。。。
! P; Y, j/ L1 ~5 c9 _0 j4 D9 n
6 d" j6 _* t; z我是这样编的，请老大帮帮忙，该如何该呀。
Private Sub Command4_Click()
* I8 d' @, ]9 N! [Dim XMAX, XMIN, YMAX, YMIN, ZMAX As long
$ g9 a. P# h9 |" i+ zPowerMILL31.Connect
PowerMILL31.Execute ("Form BLOCK")
PowerMILL31.Execute ("EDIT BLOCK ALL UNLOCK")
PowerMILL31.Execute ("EDIT BLOCK TOLERANCE 0.1")
PowerMILL31.Execute ("EDIT BLOCK RESETLIMIT 0.")
/ W2 x- W2 `, \/ Q7 u! P! `PowerMILL31.Execute ("EDIT BLOCK RESET")
9 }2 }' ]1 l# e8 k) TPowerMILL31.Execute ("BLOCK ACCEPT")
ZMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxZ")
; v- Y8 y. g7 j- y" N; @XMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxX")
5 f8 c. y  V# Q5 P7 d* jXMIN = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MinX")
" c! r4 g  M9 I& FYMAX = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MaxY")
YMIN = PowerMILL31.ExecuteEx("PRINT FORMVALUE RoughBlock.LimitFrame.MinY")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEX  " + CStr(-(XMAX - (XMAX - XMIN) / 2)))
PowerMILL31.Execute ("TRANSFORM MODEL ALL")
PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEY  " + CStr(-(YMAX - (YMAX - YMIN) / 2)))
PowerMILL31.Execute ("TRANSFORM MODEL ALL")
7 s; k' ^; }: W! \PowerMILL31.Execute ("TRANSFORM RESET TRANSFORM TYPE MOVE TRANSFORM MOVEZ   " + CStr(-ZMAX))
5 d/ S& t" ?1 e' SPowerMILL31.Execute ("TRANSFORM MODEL ALL")
- p7 [/ Z# R& S) _4 B  QPowerMILL31.Execute ("Delete BLOCK")
3 b" p& I1 d( x5 W( s* y* E! K6 lPowerMILL31.Disconnect

hh749

使用创建坐标指令来解决,

dazhi518

还是解决不了呀,,,老大.

hh749

pmill.StoreModel
xmin = pmill.BlockSize(psXMin)
( z6 }# n6 P- m( N: m, x7 r6 \XMAX = pmill.BlockSize(psXMax)
8 U' ^1 a! x; t7 h, nYMIN = pmill.BlockSize(psymin)
YMAX = pmill.BlockSize(psymax)
. Y! a+ f* C  h6 g, vZMIN = pmill.BlockSize(pszmin)
3 S4 u, x7 S9 K! xZMAX = pmill.BlockSize(pszmax)
5 l9 {  u  b; w$ |; h4 z3 \WKPLX = xmin + (XMAX - xmin) / 2
WKPLY = YMIN + (YMAX - YMIN) / 2
WKPLZ = ZMAX
pmill.Execute "CREATE WORKPLANE ;"
+ O4 {, A7 g& n/ e8 W# `( Rpmill.GetWorkplaneList WorkplaneList, ActiveWorkplane
NewWkpl = WorkplaneList(WorkplaneList.Count)
pmill.Execute "MOVE WORKPLANE  '" & NewWkpl & "' X " & Format(WKPLX) & " Y " & Format(WKPLY) & " Z " & Format(WKPLZ)
! j2 t5 i; L9 O9 y. Npml_send ("ACTIVATE Workplane " & "'" & NewWkpl & "'")
6 n$ W/ {1 C& G# m1 Gpml_send ("TRANSFORM RESET TRANSFORM TYPE WORLD TRANSFORM MODEL ALL SELECTED")
& c' _. `3 Q5 @pml_send ("DELETE Workplane " & "'" & NewWkpl & "'")
8 g' T# q+ s' z
之前给ＪＩＭ写的一个外挂的代码，这部分是建立坐标的代码，你可以参照下

[ 本帖最后由 hh749 于 2009-4-16 21:41 编辑 ]

dazhi518

太谢谢老大了，感激不尽呀。。

dazhi518

老大,能不能发个完整一点的呀，，我对宏和VB不是非常的了解呀。。。。loveshenzhichen888@126.com本人邮箱。谢谢。

hh749

自己写,编程就是要靠自己的努力去完成,老用别人的自己就没得进步,方法我已经说了!