|
|
楼主 |
发表于 2018-9-23 20:41:45
|
显示全部楼层
本帖最后由 tp7399 于 2018-9-23 20:47 编辑
; r6 t; a; n6 C( U0 p) N4 J/ _) `, {
不好意思再麻烦你一个问题,
" x# ]! ?7 b7 [4 r# q( d2 c* s( V9 f% v4 a9 [& N
在结尾要多加1个刀具检测,, p( D( E. S4 W1 I3 v$ Q
- g5 ?- V. J, N! z7 U
结果输出的刀具直径跟R角变成下一把刀的,
/ Z: | }5 `/ w2 g6 T7 U
% A, ?0 \5 m. _要怎么样改成目前加工的这把刀具呢?! o. y$ O f M. v' d5 E+ G
: e3 K5 ]$ k; r8 M0 `5 r8 x9 i--------------------------------------------------------------------
$ h( _% j- b' W% b. [7 M& g2 z+ K, z2 ?+ a( e6 a9 M
程式开始的时候,& W/ k5 k7 j4 V9 X9 f
! @' l: }: a" @* c; M: U2 ?- n+ w! A
T1
5 K; ]1 v/ y6 T6 p: y2 E9 M3 V& n4 f
M6
' @4 b3 p4 T! J+ m2 F- R# s# E. H0 u" o
T1 D1
" m z5 K; ?2 z5 f+ f# I" _: c; d- W# N! \9 q
M81(25. ,1. )$ i+ C& D; J$ }. w [2 A
7 x. Y* c# g+ ~8 U7 d. ?* Y2 a
T1 D1% p! ^- q* D+ ^0 g: h" z
- t# a, x9 ?6 H' F/ V9 A
HSCA(0.003)
5 z- _3 l" X* Y/ W8 @0 Q/ O/ M9 [ m6 I: ~* T7 D; a
G0 G90 G54 X21. Y-41.799 p2 p; ?7 {9 e! }$ Q$ e
* n; i2 t! x: i4 X5 F0 J& p3 kS2000 M3
7 Z, H; P6 U2 @& i
& Y# @# I; d Y# `8 N1 RG0 Z50.
7 Y* m# \- C5 B7 O9 m6 |& @: u0 m( J& Z' O6 Q P2 ^
上面都这些没有问题了,
8 k/ B I7 D$ X: O w1 T; j5 T) A1 `) W/ c" U
--------------------------------------------------------------------, }9 [2 q% n3 Y% p$ s. U% k
& J' }+ f' l7 Y/ k; K7 i程式结尾1 J6 R* m; t0 s x% u
" a9 G3 s2 m. ~+ n6 f- p
G0 Z50.- L' j5 i8 G2 }5 Q. A$ _
8 ~3 N+ e" ]7 r3 [; V. \M5
8 Y5 h! p. P* X. M% l6 n
5 n4 H$ L2 R4 }M9+ D8 b& T; b; j w' C8 D
" h. @) z7 @, P( a4 U
M81(4. ,0. )
8 s C# W1 E: Q( n; I2 o3 s0 C. a: r: c5 Z. ^" N S# N
M01
$ X, {4 W' k7 Z' {' h1 A2 n. v1 U$ h3 a
这边就出问题了,
: q1 p; y2 V$ b
( O7 @9 l2 C* v% b/ O+ a2 i所出现的刀具直径跟R角变成下一把刀的,: I* f; @! @2 T3 }1 O6 l/ z4 R
( F: B& @) P$ K3 r& b
--------------------------------------------------------------------4 f3 h- W; L8 V+ A/ l
& s' g% V" f/ M/ K6 M0 O下面是我自己改的代码,
1 {/ R3 B% @' B* H/ [% M- v5 K4 ?0 R+ e5 J1 R
pretract #End of tool path, toolchange ' {1 O2 l- L5 `/ i
sav_absinc = absinc$3 G& u8 g' u0 L* y
absinc$ = one' @6 @2 y( F z7 ~, X
sav_coolant = coolant$) l4 Z, F1 h( Q8 \) D+ Y) V
coolant$ = zero9 w# a3 W0 X) A t3 H5 q5 v
#cc_pos is reset in the toolchange here
+ _* ]. e/ h( X* ~ cc_pos$ = zero
, g) F; ]: g+ b/ z gcode$ = zero
: S$ |# A8 z" B9 X ]2 X pbld, n$, sccomp, *sm05, psub_end_mny, e$
% V" o0 e, S# m/ }8 F- M( h scoolant, e$9 Q8 E7 l5 Z! V8 X9 E5 A. J
pbld, n$, "M81(", *tldia$, ",", *tcr, ")", e$
7 L6 y+ A( i! H8 q9 b) H5 U #pbld, n$, sgabsinc, sgcode, *sg28ref, "Z0.", e$
/ F0 F2 E7 p! k
* W4 @1 S6 j$ H, g--------------------------------------------------------------------9 n3 V. h! h6 o
/ U: f8 K x) M4 C
在此先谢谢大神
& M4 x9 M0 i0 O8 J/ q0 j) B- r5 x3 S; U# b8 e5 y1 z6 t
最后祝大神中秋快乐
: O7 w" X3 m- ^* |- r5 e: g. i8 |7 ~1 O8 ~! J$ U
* H, K0 u0 z& f! l! L6 }# ?; ?
! y( q5 Q' R. g% h7 _# F% a+ |' I6 a' N1 X0 z l, f
|
|
发表于 2018-9-22 08:14:12